| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net/rds: reset op_nents when zerocopy page pin fails
When iov_iter_get_pages2() fails in rds_message_zcopy_from_user(),
the pinned pages are released with put_page(), and
rm->data.op_mmp_znotifier is cleared. But we fail to properly
clear rm->data.op_nents.
Later when rds_message_purge() is called from rds_sendmsg() the
cleanup loop iterates over the incorrectly non zero number of
op_nents and frees them again.
Fix this by properly resetting op_nents when it should be in
rds_message_zcopy_from_user(). |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: x_tables: guard option walkers against 1-byte tail reads
When the last byte of options is a non-single-byte option kind, walkers
that advance with i += op[i + 1] ? : 1 can read op[i + 1] past the end
of the option area.
Add an explicit i == optlen - 1 check before dereferencing op[i + 1]
in xt_tcpudp and xt_dccp option walkers. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: Use u32 for non-negative values in ceph_monmap_decode()
This patch fixes unnecessary implicit conversions that change signedness
of blob_len and num_mon in ceph_monmap_decode().
Currently blob_len and num_mon are (signed) int variables. They are used
to hold values that are always non-negative and get assigned in
ceph_decode_32_safe(), which is meant to assign u32 values. Both
variables are subsequently used as unsigned values, and the value of
num_mon is further assigned to monmap->num_mon, which is of type u32.
Therefore, both variables should be of type u32. This is especially
relevant for num_mon. If the value read from the incoming message is
very large, it is interpreted as a negative value, and the check for
num_mon > CEPH_MAX_MON does not catch it. This leads to the attempt to
allocate a very large chunk of memory for monmap, which will most likely
fail. In this case, an unnecessary attempt to allocate memory is
performed, and -ENOMEM is returned instead of -EINVAL. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: fix undersized l_iclog_roundoff values
If the superblock doesn't list a log stripe unit, we set the incore log
roundoff value to 512. This leads to corrupt logs and unmountable
filesystems in generic/617 on a disk with 4k physical sectors...
XFS (sda1): Mounting V5 Filesystem ff3121ca-26e6-4b77-b742-aaff9a449e1c
XFS (sda1): Torn write (CRC failure) detected at log block 0x318e. Truncating head block from 0x3197.
XFS (sda1): failed to locate log tail
XFS (sda1): log mount/recovery failed: error -74
XFS (sda1): log mount failed
XFS (sda1): Mounting V5 Filesystem ff3121ca-26e6-4b77-b742-aaff9a449e1c
XFS (sda1): Ending clean mount
...on the current xfsprogs for-next which has a broken mkfs. xfs_info
shows this...
meta-data=/dev/sda1 isize=512 agcount=4, agsize=644992 blks
= sectsz=4096 attr=2, projid32bit=1
= crc=1 finobt=1, sparse=1, rmapbt=1
= reflink=1 bigtime=1 inobtcount=1 nrext64=1
= exchange=1 metadir=1
data = bsize=4096 blocks=2579968, imaxpct=25
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0, ftype=1, parent=1
log =internal log bsize=4096 blocks=16384, version=2
= sectsz=4096 sunit=0 blks, lazy-count=1
realtime =none extsz=4096 blocks=0, rtextents=0
= rgcount=0 rgsize=268435456 extents
= zoned=0 start=0 reserved=0
...observe that the log section has sectsz=4096 sunit=0, which means
that the roundoff factor is 512, not 4096 as you'd expect. We should
fix mkfs not to generate broken filesystems, but anyone can fuzz the
ondisk superblock so we should be more cautious. I think the inadequate
logic predates commit a6a65fef5ef8d0, but that's clearly going to
require a different backport. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: require a full NFS mode SID before reading mode bits
parse_dacl() treats an ACE SID matching sid_unix_NFS_mode as an NFS
mode SID and reads sid.sub_auth[2] to recover the mode bits.
That assumes the ACE carries three subauthorities, but compare_sids()
only compares min(a, b) subauthorities. A malicious server can return
an ACE with num_subauth = 2 and sub_auth[] = {88, 3}, which still
matches sid_unix_NFS_mode and then drives the sub_auth[2] read four
bytes past the end of the ACE.
Require num_subauth >= 3 before treating the ACE as an NFS mode SID.
This keeps the fix local to the special-SID mode path without changing
compare_sids() semantics for the rest of cifsacl. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: flowtable: strictly check for maximum number of actions
The maximum number of flowtable hardware offload actions in IPv6 is:
* ethernet mangling (4 payload actions, 2 for each ethernet address)
* SNAT (4 payload actions)
* DNAT (4 payload actions)
* Double VLAN (4 vlan actions, 2 for popping vlan, and 2 for pushing)
for QinQ.
* Redirect (1 action)
Which makes 17, while the maximum is 16. But act_ct supports for tunnels
actions too. Note that payload action operates at 32-bit word level, so
mangling an IPv6 address takes 4 payload actions.
Update flow_action_entry_next() calls to check for the maximum number of
supported actions.
While at it, rise the maximum number of actions per flow from 16 to 24
so this works fine with IPv6 setups. |
| In the Linux kernel, the following vulnerability has been resolved:
libceph: define and enforce CEPH_MAX_KEY_LEN
When decoding the key, verify that the key material would fit into
a fixed-size buffer in process_auth_done() and generally has a sane
length.
The new CEPH_MAX_KEY_LEN check replaces the existing check for a key
with no key material which is a) not universal since CEPH_CRYPTO_NONE
has to be excluded and b) doesn't provide much value since a smaller
than needed key is just as invalid as no key -- this has to be handled
elsewhere anyway. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: ioam: fix heap buffer overflow in __ioam6_fill_trace_data()
On the receive path, __ioam6_fill_trace_data() uses trace->nodelen
to decide how much data to write for each node. It trusts this field
as-is from the incoming packet, with no consistency check against
trace->type (the 24-bit field that tells which data items are
present). A crafted packet can set nodelen=0 while setting type bits
0-21, causing the function to write ~100 bytes past the allocated
region (into skb_shared_info), which corrupts adjacent heap memory
and leads to a kernel panic.
Add a shared helper ioam6_trace_compute_nodelen() in ioam6.c to
derive the expected nodelen from the type field, and use it:
- in ioam6_iptunnel.c (send path, existing validation) to replace
the open-coded computation;
- in exthdrs.c (receive path, ipv6_hop_ioam) to drop packets whose
nodelen is inconsistent with the type field, before any data is
written.
Per RFC 9197, bits 12-21 are each short (4-octet) fields, so they
are included in IOAM6_MASK_SHORT_FIELDS (changed from 0xff100000 to
0xff1ffc00). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: pci: validate release report content before using for RTL8922DE
The commit 957eda596c76
("wifi: rtw89: pci: validate sequence number of TX release report")
does validation on existing chips, which somehow a release report of SKB
becomes malformed. As no clear cause found, add rules ahead for RTL8922DE
to avoid crash if it happens. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: fix freemap adjustments when adding xattrs to leaf blocks
xfs/592 and xfs/794 both trip this assertion in the leaf block freemap
adjustment code after ~20 minutes of running on my test VMs:
ASSERT(ichdr->firstused >= ichdr->count * sizeof(xfs_attr_leaf_entry_t)
+ xfs_attr3_leaf_hdr_size(leaf));
Upon enabling quite a lot more debugging code, I narrowed this down to
fsstress trying to set a local extended attribute with namelen=3 and
valuelen=71. This results in an entry size of 80 bytes.
At the start of xfs_attr3_leaf_add_work, the freemap looks like this:
i 0 base 448 size 0 rhs 448 count 46
i 1 base 388 size 132 rhs 448 count 46
i 2 base 2120 size 4 rhs 448 count 46
firstused = 520
where "rhs" is the first byte past the end of the leaf entry array.
This is inconsistent -- the entries array ends at byte 448, but
freemap[1] says there's free space starting at byte 388!
By the end of the function, the freemap is in worse shape:
i 0 base 456 size 0 rhs 456 count 47
i 1 base 388 size 52 rhs 456 count 47
i 2 base 2120 size 4 rhs 456 count 47
firstused = 440
Important note: 388 is not aligned with the entries array element size
of 8 bytes.
Based on the incorrect freemap, the name area starts at byte 440, which
is below the end of the entries array! That's why the assertion
triggers and the filesystem shuts down.
How did we end up here? First, recall from the previous patch that the
freemap array in an xattr leaf block is not intended to be a
comprehensive map of all free space in the leaf block. In other words,
it's perfectly legal to have a leaf block with:
* 376 bytes in use by the entries array
* freemap[0] has [base = 376, size = 8]
* freemap[1] has [base = 388, size = 1500]
* the space between 376 and 388 is free, but the freemap stopped
tracking that some time ago
If we add one xattr, the entries array grows to 384 bytes, and
freemap[0] becomes [base = 384, size = 0]. So far, so good. But if we
add a second xattr, the entries array grows to 392 bytes, and freemap[0]
gets pushed up to [base = 392, size = 0]. This is bad, because
freemap[1] hasn't been updated, and now the entries array and the free
space claim the same space.
The fix here is to adjust all freemap entries so that none of them
collide with the entries array. Note that this fix relies on commit
2a2b5932db6758 ("xfs: fix attr leaf header freemap.size underflow") and
the previous patch that resets zero length freemap entries to have
base = 0. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/arm-cmn: Reject unsupported hardware configurations
So far we've been fairly lax about accepting both unknown CMN models
(at least with a warning), and unknown revisions of those which we
do know, as although things do frequently change between releases,
typically enough remains the same to be somewhat useful for at least
some basic bringup checks. However, we also make assumptions of the
maximum supported sizes and numbers of things in various places, and
there's no guarantee that something new might not be bigger and lead
to nasty array overflows. Make sure we only try to run on things that
actually match our assumptions and so will not risk memory corruption.
We have at least always failed on completely unknown node types, so
update that error message for clarity and consistency too. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: Fix missing key size check for L2CAP_LE_CONN_REQ
This adds a check for encryption key size upon receiving
L2CAP_LE_CONN_REQ which is required by L2CAP/LE/CFC/BV-15-C which
expects L2CAP_CR_LE_BAD_KEY_SIZE. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: validate bsscfg indices in IF events
brcmf_fweh_handle_if_event() validates the firmware-provided interface
index before it touches drvr->iflist[], but it still uses the raw
bsscfgidx field as an array index without a matching range check.
Reject IF events whose bsscfg index does not fit in drvr->iflist[]
before indexing the interface array.
[add missing wifi prefix] |
| In the Linux kernel, the following vulnerability has been resolved:
xsk: tighten UMEM headroom validation to account for tailroom and min frame
The current headroom validation in xdp_umem_reg() could leave us with
insufficient space dedicated to even receive minimum-sized ethernet
frame. Furthermore if multi-buffer would come to play then
skb_shared_info stored at the end of XSK frame would be corrupted.
HW typically works with 128-aligned sizes so let us provide this value
as bare minimum.
Multi-buffer setting is known later in the configuration process so
besides accounting for 128 bytes, let us also take care of tailroom space
upfront. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: handle wraparound when searching for blocks for indirect mapped blocks
Commit 4865c768b563 ("ext4: always allocate blocks only from groups
inode can use") restricts what blocks will be allocated for indirect
block based files to block numbers that fit within 32-bit block
numbers.
However, when using a review bot running on the latest Gemini LLM to
check this commit when backporting into an LTS based kernel, it raised
this concern:
If ac->ac_g_ex.fe_group is >= ngroups (for instance, if the goal
group was populated via stream allocation from s_mb_last_groups),
then start will be >= ngroups.
Does this allow allocating blocks beyond the 32-bit limit for
indirect block mapped files? The commit message mentions that
ext4_mb_scan_groups_linear() takes care to not select unsupported
groups. However, its loop uses group = *start, and the very first
iteration will call ext4_mb_scan_group() with this unsupported
group because next_linear_group() is only called at the end of the
iteration.
After reviewing the code paths involved and considering the LLM
review, I determined that this can happen when there is a file system
where some files/directories are extent-mapped and others are
indirect-block mapped. To address this, add a safety clamp in
ext4_mb_scan_groups(). |
| In the Linux kernel, the following vulnerability has been resolved:
HID: multitouch: Check to ensure report responses match the request
It is possible for a malicious (or clumsy) device to respond to a
specific report's feature request using a completely different report
ID. This can cause confusion in the HID core resulting in nasty
side-effects such as OOB writes.
Add a check to ensure that the report ID in the response, matches the
one that was requested. If it doesn't, omit reporting the raw event and
return early. |
| In the Linux kernel, the following vulnerability has been resolved:
ip6_tunnel: clear skb2->cb[] in ip4ip6_err()
Oskar Kjos reported the following problem.
ip4ip6_err() calls icmp_send() on a cloned skb whose cb[] was written
by the IPv6 receive path as struct inet6_skb_parm. icmp_send() passes
IPCB(skb2) to __ip_options_echo(), which interprets that cb[] region
as struct inet_skb_parm (IPv4). The layouts differ: inet6_skb_parm.nhoff
at offset 14 overlaps inet_skb_parm.opt.rr, producing a non-zero rr
value. __ip_options_echo() then reads optlen from attacker-controlled
packet data at sptr[rr+1] and copies that many bytes into dopt->__data,
a fixed 40-byte stack buffer (IP_OPTIONS_DATA_FIXED_SIZE).
To fix this we clear skb2->cb[], as suggested by Oskar Kjos.
Also add minimal IPv4 header validation (version == 4, ihl >= 5). |
| In the Linux kernel, the following vulnerability has been resolved:
Buffer overflow in drivers/xen/sys-hypervisor.c
The build id returned by HYPERVISOR_xen_version(XENVER_build_id) is
neither NUL terminated nor a string.
The first causes a buffer overflow as sprintf in buildid_show will
read and copy till it finds a NUL.
00000000 f4 91 51 f4 dd 38 9e 9d 65 47 52 eb 10 71 db 50 |..Q..8..eGR..q.P|
00000010 b9 a8 01 42 6f 2e 32 |...Bo.2|
00000017
So use a memcpy instead of sprintf to have the correct value:
00000000 f4 91 51 f4 dd 00 9e 9d 65 47 52 eb 10 71 db 50 |..Q.....eGR..q.P|
00000010 b9 a8 01 42 |...B|
00000014
(the above have a hack to embed a zero inside and check it's
returned correctly).
This is XSA-485 / CVE-2026-31786 |
| In the Linux kernel, the following vulnerability has been resolved:
io_uring/net: fix slab-out-of-bounds read in io_bundle_nbufs()
sqe->len is __u32 but gets stored into sr->len which is int. When
userspace passes sqe->len values exceeding INT_MAX (e.g. 0xFFFFFFFF),
sr->len overflows to a negative value. This negative value propagates
through the bundle recv/send path:
1. io_recv(): sel.val = sr->len (ssize_t gets -1)
2. io_recv_buf_select(): arg.max_len = sel->val (size_t gets
0xFFFFFFFFFFFFFFFF)
3. io_ring_buffers_peek(): buf->len is not clamped because max_len
is astronomically large
4. iov[].iov_len = 0xFFFFFFFF flows into io_bundle_nbufs()
5. io_bundle_nbufs(): min_t(int, 0xFFFFFFFF, ret) yields -1,
causing ret to increase instead of decrease, creating an
infinite loop that reads past the allocated iov[] array
This results in a slab-out-of-bounds read in io_bundle_nbufs() from
the kmalloc-64 slab, as nbufs increments past the allocated iovec
entries.
BUG: KASAN: slab-out-of-bounds in io_bundle_nbufs+0x128/0x160
Read of size 8 at addr ffff888100ae05c8 by task exp/145
Call Trace:
io_bundle_nbufs+0x128/0x160
io_recv_finish+0x117/0xe20
io_recv+0x2db/0x1160
Fix this by rejecting negative sr->len values early in both
io_sendmsg_prep() and io_recvmsg_prep(). Since sqe->len is __u32,
any value > INT_MAX indicates overflow and is not a valid length. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: fix stack buffer overflow in hci_le_big_create_sync
hci_le_big_create_sync() uses DEFINE_FLEX to allocate a
struct hci_cp_le_big_create_sync on the stack with room for 0x11 (17)
BIS entries. However, conn->num_bis can hold up to HCI_MAX_ISO_BIS (31)
entries — validated against ISO_MAX_NUM_BIS (0x1f) in the caller
hci_conn_big_create_sync(). When conn->num_bis is between 18 and 31,
the memcpy that copies conn->bis into cp->bis writes up to 14 bytes
past the stack buffer, corrupting adjacent stack memory.
This is trivially reproducible: binding an ISO socket with
bc_num_bis = ISO_MAX_NUM_BIS (31) and calling listen() will
eventually trigger hci_le_big_create_sync() from the HCI command
sync worker, causing a KASAN-detectable stack-out-of-bounds write:
BUG: KASAN: stack-out-of-bounds in hci_le_big_create_sync+0x256/0x3b0
Write of size 31 at addr ffffc90000487b48 by task kworker/u9:0/71
Fix this by changing the DEFINE_FLEX count from the incorrect 0x11 to
HCI_MAX_ISO_BIS, which matches the maximum number of BIS entries that
conn->bis can actually carry. |
