| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: bridge: fix soft lockup in br_multicast_query_expired()
When set multicast_query_interval to a large value, the local variable
'time' in br_multicast_send_query() may overflow. If the time is smaller
than jiffies, the timer will expire immediately, and then call mod_timer()
again, which creates a loop and may trigger the following soft lockup
issue.
watchdog: BUG: soft lockup - CPU#1 stuck for 221s! [rb_consumer:66]
CPU: 1 UID: 0 PID: 66 Comm: rb_consumer Not tainted 6.16.0+ #259 PREEMPT(none)
Call Trace:
<IRQ>
__netdev_alloc_skb+0x2e/0x3a0
br_ip6_multicast_alloc_query+0x212/0x1b70
__br_multicast_send_query+0x376/0xac0
br_multicast_send_query+0x299/0x510
br_multicast_query_expired.constprop.0+0x16d/0x1b0
call_timer_fn+0x3b/0x2a0
__run_timers+0x619/0x950
run_timer_softirq+0x11c/0x220
handle_softirqs+0x18e/0x560
__irq_exit_rcu+0x158/0x1a0
sysvec_apic_timer_interrupt+0x76/0x90
</IRQ>
This issue can be reproduced with:
ip link add br0 type bridge
echo 1 > /sys/class/net/br0/bridge/multicast_querier
echo 0xffffffffffffffff >
/sys/class/net/br0/bridge/multicast_query_interval
ip link set dev br0 up
The multicast_startup_query_interval can also cause this issue. Similar to
the commit 99b40610956a ("net: bridge: mcast: add and enforce query
interval minimum"), add check for the query interval maximum to fix this
issue. |
| In the Linux kernel, the following vulnerability has been resolved:
net: gso: Forbid IPv6 TSO with extensions on devices with only IPV6_CSUM
When performing Generic Segmentation Offload (GSO) on an IPv6 packet that
contains extension headers, the kernel incorrectly requests checksum offload
if the egress device only advertises NETIF_F_IPV6_CSUM feature, which has
a strict contract: it supports checksum offload only for plain TCP or UDP
over IPv6 and explicitly does not support packets with extension headers.
The current GSO logic violates this contract by failing to disable the feature
for packets with extension headers, such as those used in GREoIPv6 tunnels.
This violation results in the device being asked to perform an operation
it cannot support, leading to a `skb_warn_bad_offload` warning and a collapse
of network throughput. While device TSO/USO is correctly bypassed in favor
of software GSO for these packets, the GSO stack must be explicitly told not
to request checksum offload.
Mask NETIF_F_IPV6_CSUM, NETIF_F_TSO6 and NETIF_F_GSO_UDP_L4
in gso_features_check if the IPv6 header contains extension headers to compute
checksum in software.
The exception is a BIG TCP extension, which, as stated in commit
68e068cabd2c6c53 ("net: reenable NETIF_F_IPV6_CSUM offload for BIG TCP packets"):
"The feature is only enabled on devices that support BIG TCP TSO.
The header is only present for PF_PACKET taps like tcpdump,
and not transmitted by physical devices."
kernel log output (truncated):
WARNING: CPU: 1 PID: 5273 at net/core/dev.c:3535 skb_warn_bad_offload+0x81/0x140
...
Call Trace:
<TASK>
skb_checksum_help+0x12a/0x1f0
validate_xmit_skb+0x1a3/0x2d0
validate_xmit_skb_list+0x4f/0x80
sch_direct_xmit+0x1a2/0x380
__dev_xmit_skb+0x242/0x670
__dev_queue_xmit+0x3fc/0x7f0
ip6_finish_output2+0x25e/0x5d0
ip6_finish_output+0x1fc/0x3f0
ip6_tnl_xmit+0x608/0xc00 [ip6_tunnel]
ip6gre_tunnel_xmit+0x1c0/0x390 [ip6_gre]
dev_hard_start_xmit+0x63/0x1c0
__dev_queue_xmit+0x6d0/0x7f0
ip6_finish_output2+0x214/0x5d0
ip6_finish_output+0x1fc/0x3f0
ip6_xmit+0x2ca/0x6f0
ip6_finish_output+0x1fc/0x3f0
ip6_xmit+0x2ca/0x6f0
inet6_csk_xmit+0xeb/0x150
__tcp_transmit_skb+0x555/0xa80
tcp_write_xmit+0x32a/0xe90
tcp_sendmsg_locked+0x437/0x1110
tcp_sendmsg+0x2f/0x50
...
skb linear: 00000000: e4 3d 1a 7d ec 30 e4 3d 1a 7e 5d 90 86 dd 60 0e
skb linear: 00000010: 00 0a 1b 34 3c 40 20 11 00 00 00 00 00 00 00 00
skb linear: 00000020: 00 00 00 00 00 12 20 11 00 00 00 00 00 00 00 00
skb linear: 00000030: 00 00 00 00 00 11 2f 00 04 01 04 01 01 00 00 00
skb linear: 00000040: 86 dd 60 0e 00 0a 1b 00 06 40 20 23 00 00 00 00
skb linear: 00000050: 00 00 00 00 00 00 00 00 00 12 20 23 00 00 00 00
skb linear: 00000060: 00 00 00 00 00 00 00 00 00 11 bf 96 14 51 13 f9
skb linear: 00000070: ae 27 a0 a8 2b e3 80 18 00 40 5b 6f 00 00 01 01
skb linear: 00000080: 08 0a 42 d4 50 d5 4b 70 f8 1a |
| In the Linux kernel, the following vulnerability has been resolved:
fs: Prevent file descriptor table allocations exceeding INT_MAX
When sysctl_nr_open is set to a very high value (for example, 1073741816
as set by systemd), processes attempting to use file descriptors near
the limit can trigger massive memory allocation attempts that exceed
INT_MAX, resulting in a WARNING in mm/slub.c:
WARNING: CPU: 0 PID: 44 at mm/slub.c:5027 __kvmalloc_node_noprof+0x21a/0x288
This happens because kvmalloc_array() and kvmalloc() check if the
requested size exceeds INT_MAX and emit a warning when the allocation is
not flagged with __GFP_NOWARN.
Specifically, when nr_open is set to 1073741816 (0x3ffffff8) and a
process calls dup2(oldfd, 1073741880), the kernel attempts to allocate:
- File descriptor array: 1073741880 * 8 bytes = 8,589,935,040 bytes
- Multiple bitmaps: ~400MB
- Total allocation size: > 8GB (exceeding INT_MAX = 2,147,483,647)
Reproducer:
1. Set /proc/sys/fs/nr_open to 1073741816:
# echo 1073741816 > /proc/sys/fs/nr_open
2. Run a program that uses a high file descriptor:
#include <unistd.h>
#include <sys/resource.h>
int main() {
struct rlimit rlim = {1073741824, 1073741824};
setrlimit(RLIMIT_NOFILE, &rlim);
dup2(2, 1073741880); // Triggers the warning
return 0;
}
3. Observe WARNING in dmesg at mm/slub.c:5027
systemd commit a8b627a introduced automatic bumping of fs.nr_open to the
maximum possible value. The rationale was that systems with memory
control groups (memcg) no longer need separate file descriptor limits
since memory is properly accounted. However, this change overlooked
that:
1. The kernel's allocation functions still enforce INT_MAX as a maximum
size regardless of memcg accounting
2. Programs and tests that legitimately test file descriptor limits can
inadvertently trigger massive allocations
3. The resulting allocations (>8GB) are impractical and will always fail
systemd's algorithm starts with INT_MAX and keeps halving the value
until the kernel accepts it. On most systems, this results in nr_open
being set to 1073741816 (0x3ffffff8), which is just under 1GB of file
descriptors.
While processes rarely use file descriptors near this limit in normal
operation, certain selftests (like
tools/testing/selftests/core/unshare_test.c) and programs that test file
descriptor limits can trigger this issue.
Fix this by adding a check in alloc_fdtable() to ensure the requested
allocation size does not exceed INT_MAX. This causes the operation to
fail with -EMFILE instead of triggering a kernel warning and avoids the
impractical >8GB memory allocation request. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: asix_devices: Fix PHY address mask in MDIO bus initialization
Syzbot reported shift-out-of-bounds exception on MDIO bus initialization.
The PHY address should be masked to 5 bits (0-31). Without this
mask, invalid PHY addresses could be used, potentially causing issues
with MDIO bus operations.
Fix this by masking the PHY address with 0x1f (31 decimal) to ensure
it stays within the valid range. |
| In the Linux kernel, the following vulnerability has been resolved:
netlink: avoid infinite retry looping in netlink_unicast()
netlink_attachskb() checks for the socket's read memory allocation
constraints. Firstly, it has:
rmem < READ_ONCE(sk->sk_rcvbuf)
to check if the just increased rmem value fits into the socket's receive
buffer. If not, it proceeds and tries to wait for the memory under:
rmem + skb->truesize > READ_ONCE(sk->sk_rcvbuf)
The checks don't cover the case when skb->truesize + sk->sk_rmem_alloc is
equal to sk->sk_rcvbuf. Thus the function neither successfully accepts
these conditions, nor manages to reschedule the task - and is called in
retry loop for indefinite time which is caught as:
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 0-....: (25999 ticks this GP) idle=ef2/1/0x4000000000000000 softirq=262269/262269 fqs=6212
(t=26000 jiffies g=230833 q=259957)
NMI backtrace for cpu 0
CPU: 0 PID: 22 Comm: kauditd Not tainted 5.10.240 #68
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc42 04/01/2014
Call Trace:
<IRQ>
dump_stack lib/dump_stack.c:120
nmi_cpu_backtrace.cold lib/nmi_backtrace.c:105
nmi_trigger_cpumask_backtrace lib/nmi_backtrace.c:62
rcu_dump_cpu_stacks kernel/rcu/tree_stall.h:335
rcu_sched_clock_irq.cold kernel/rcu/tree.c:2590
update_process_times kernel/time/timer.c:1953
tick_sched_handle kernel/time/tick-sched.c:227
tick_sched_timer kernel/time/tick-sched.c:1399
__hrtimer_run_queues kernel/time/hrtimer.c:1652
hrtimer_interrupt kernel/time/hrtimer.c:1717
__sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1113
asm_call_irq_on_stack arch/x86/entry/entry_64.S:808
</IRQ>
netlink_attachskb net/netlink/af_netlink.c:1234
netlink_unicast net/netlink/af_netlink.c:1349
kauditd_send_queue kernel/audit.c:776
kauditd_thread kernel/audit.c:897
kthread kernel/kthread.c:328
ret_from_fork arch/x86/entry/entry_64.S:304
Restore the original behavior of the check which commit in Fixes
accidentally missed when restructuring the code.
Found by Linux Verification Center (linuxtesting.org). |
| In the Linux kernel, the following vulnerability has been resolved:
rcu/nocb: Fix possible invalid rdp's->nocb_cb_kthread pointer access
In the preparation stage of CPU online, if the corresponding
the rdp's->nocb_cb_kthread does not exist, will be created,
there is a situation where the rdp's rcuop kthreads creation fails,
and then de-offload this CPU's rdp, does not assign this CPU's
rdp->nocb_cb_kthread pointer, but this rdp's->nocb_gp_rdp and
rdp's->rdp_gp->nocb_gp_kthread is still valid.
This will cause the subsequent re-offload operation of this offline
CPU, which will pass the conditional check and the kthread_unpark()
will access invalid rdp's->nocb_cb_kthread pointer.
This commit therefore use rdp's->nocb_gp_kthread instead of
rdp_gp's->nocb_gp_kthread for safety check. |
| In the Linux kernel, the following vulnerability has been resolved:
eventpoll: Fix semi-unbounded recursion
Ensure that epoll instances can never form a graph deeper than
EP_MAX_NESTS+1 links.
Currently, ep_loop_check_proc() ensures that the graph is loop-free and
does some recursion depth checks, but those recursion depth checks don't
limit the depth of the resulting tree for two reasons:
- They don't look upwards in the tree.
- If there are multiple downwards paths of different lengths, only one of
the paths is actually considered for the depth check since commit
28d82dc1c4ed ("epoll: limit paths").
Essentially, the current recursion depth check in ep_loop_check_proc() just
serves to prevent it from recursing too deeply while checking for loops.
A more thorough check is done in reverse_path_check() after the new graph
edge has already been created; this checks, among other things, that no
paths going upwards from any non-epoll file with a length of more than 5
edges exist. However, this check does not apply to non-epoll files.
As a result, it is possible to recurse to a depth of at least roughly 500,
tested on v6.15. (I am unsure if deeper recursion is possible; and this may
have changed with commit 8c44dac8add7 ("eventpoll: Fix priority inversion
problem").)
To fix it:
1. In ep_loop_check_proc(), note the subtree depth of each visited node,
and use subtree depths for the total depth calculation even when a subtree
has already been visited.
2. Add ep_get_upwards_depth_proc() for similarly determining the maximum
depth of an upwards walk.
3. In ep_loop_check(), use these values to limit the total path length
between epoll nodes to EP_MAX_NESTS edges. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject narrower access to pointer ctx fields
The following BPF program, simplified from a syzkaller repro, causes a
kernel warning:
r0 = *(u8 *)(r1 + 169);
exit;
With pointer field sk being at offset 168 in __sk_buff. This access is
detected as a narrower read in bpf_skb_is_valid_access because it
doesn't match offsetof(struct __sk_buff, sk). It is therefore allowed
and later proceeds to bpf_convert_ctx_access. Note that for the
"is_narrower_load" case in the convert_ctx_accesses(), the insn->off
is aligned, so the cnt may not be 0 because it matches the
offsetof(struct __sk_buff, sk) in the bpf_convert_ctx_access. However,
the target_size stays 0 and the verifier errors with a kernel warning:
verifier bug: error during ctx access conversion(1)
This patch fixes that to return a proper "invalid bpf_context access
off=X size=Y" error on the load instruction.
The same issue affects multiple other fields in context structures that
allow narrow access. Some other non-affected fields (for sk_msg,
sk_lookup, and sockopt) were also changed to use bpf_ctx_range_ptr for
consistency.
Note this syzkaller crash was reported in the "Closes" link below, which
used to be about a different bug, fixed in
commit fce7bd8e385a ("bpf/verifier: Handle BPF_LOAD_ACQ instructions
in insn_def_regno()"). Because syzbot somehow confused the two bugs,
the new crash and repro didn't get reported to the mailing list. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel: Fix crash in icl_update_topdown_event()
The perf_fuzzer found a hard-lockup crash on a RaptorLake machine:
Oops: general protection fault, maybe for address 0xffff89aeceab400: 0000
CPU: 23 UID: 0 PID: 0 Comm: swapper/23
Tainted: [W]=WARN
Hardware name: Dell Inc. Precision 9660/0VJ762
RIP: 0010:native_read_pmc+0x7/0x40
Code: cc e8 8d a9 01 00 48 89 03 5b cd cc cc cc cc 0f 1f ...
RSP: 000:fffb03100273de8 EFLAGS: 00010046
....
Call Trace:
<TASK>
icl_update_topdown_event+0x165/0x190
? ktime_get+0x38/0xd0
intel_pmu_read_event+0xf9/0x210
__perf_event_read+0xf9/0x210
CPUs 16-23 are E-core CPUs that don't support the perf metrics feature.
The icl_update_topdown_event() should not be invoked on these CPUs.
It's a regression of commit:
f9bdf1f95339 ("perf/x86/intel: Avoid disable PMU if !cpuc->enabled in sample read")
The bug introduced by that commit is that the is_topdown_event() function
is mistakenly used to replace the is_topdown_count() call to check if the
topdown functions for the perf metrics feature should be invoked.
Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSD: fix race between nfsd registration and exports_proc
As of now nfsd calls create_proc_exports_entry() at start of init_nfsd
and cleanup by remove_proc_entry() at last of exit_nfsd.
Which causes kernel OOPs if there is race between below 2 operations:
(i) exportfs -r
(ii) mount -t nfsd none /proc/fs/nfsd
for 5.4 kernel ARM64:
CPU 1:
el1_irq+0xbc/0x180
arch_counter_get_cntvct+0x14/0x18
running_clock+0xc/0x18
preempt_count_add+0x88/0x110
prep_new_page+0xb0/0x220
get_page_from_freelist+0x2d8/0x1778
__alloc_pages_nodemask+0x15c/0xef0
__vmalloc_node_range+0x28c/0x478
__vmalloc_node_flags_caller+0x8c/0xb0
kvmalloc_node+0x88/0xe0
nfsd_init_net+0x6c/0x108 [nfsd]
ops_init+0x44/0x170
register_pernet_operations+0x114/0x270
register_pernet_subsys+0x34/0x50
init_nfsd+0xa8/0x718 [nfsd]
do_one_initcall+0x54/0x2e0
CPU 2 :
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010
PC is at : exports_net_open+0x50/0x68 [nfsd]
Call trace:
exports_net_open+0x50/0x68 [nfsd]
exports_proc_open+0x2c/0x38 [nfsd]
proc_reg_open+0xb8/0x198
do_dentry_open+0x1c4/0x418
vfs_open+0x38/0x48
path_openat+0x28c/0xf18
do_filp_open+0x70/0xe8
do_sys_open+0x154/0x248
Sometimes it crashes at exports_net_open() and sometimes cache_seq_next_rcu().
and same is happening on latest 6.14 kernel as well:
[ 0.000000] Linux version 6.14.0-rc5-next-20250304-dirty
...
[ 285.455918] Unable to handle kernel paging request at virtual address 00001f4800001f48
...
[ 285.464902] pc : cache_seq_next_rcu+0x78/0xa4
...
[ 285.469695] Call trace:
[ 285.470083] cache_seq_next_rcu+0x78/0xa4 (P)
[ 285.470488] seq_read+0xe0/0x11c
[ 285.470675] proc_reg_read+0x9c/0xf0
[ 285.470874] vfs_read+0xc4/0x2fc
[ 285.471057] ksys_read+0x6c/0xf4
[ 285.471231] __arm64_sys_read+0x1c/0x28
[ 285.471428] invoke_syscall+0x44/0x100
[ 285.471633] el0_svc_common.constprop.0+0x40/0xe0
[ 285.471870] do_el0_svc_compat+0x1c/0x34
[ 285.472073] el0_svc_compat+0x2c/0x80
[ 285.472265] el0t_32_sync_handler+0x90/0x140
[ 285.472473] el0t_32_sync+0x19c/0x1a0
[ 285.472887] Code: f9400885 93407c23 937d7c27 11000421 (f86378a3)
[ 285.473422] ---[ end trace 0000000000000000 ]---
It reproduced simply with below script:
while [ 1 ]
do
/exportfs -r
done &
while [ 1 ]
do
insmod /nfsd.ko
mount -t nfsd none /proc/fs/nfsd
umount /proc/fs/nfsd
rmmod nfsd
done &
So exporting interfaces to user space shall be done at last and
cleanup at first place.
With change there is no Kernel OOPs. |
| In the Linux kernel, the following vulnerability has been resolved:
net: clear the dst when changing skb protocol
A not-so-careful NAT46 BPF program can crash the kernel
if it indiscriminately flips ingress packets from v4 to v6:
BUG: kernel NULL pointer dereference, address: 0000000000000000
ip6_rcv_core (net/ipv6/ip6_input.c:190:20)
ipv6_rcv (net/ipv6/ip6_input.c:306:8)
process_backlog (net/core/dev.c:6186:4)
napi_poll (net/core/dev.c:6906:9)
net_rx_action (net/core/dev.c:7028:13)
do_softirq (kernel/softirq.c:462:3)
netif_rx (net/core/dev.c:5326:3)
dev_loopback_xmit (net/core/dev.c:4015:2)
ip_mc_finish_output (net/ipv4/ip_output.c:363:8)
NF_HOOK (./include/linux/netfilter.h:314:9)
ip_mc_output (net/ipv4/ip_output.c:400:5)
dst_output (./include/net/dst.h:459:9)
ip_local_out (net/ipv4/ip_output.c:130:9)
ip_send_skb (net/ipv4/ip_output.c:1496:8)
udp_send_skb (net/ipv4/udp.c:1040:8)
udp_sendmsg (net/ipv4/udp.c:1328:10)
The output interface has a 4->6 program attached at ingress.
We try to loop the multicast skb back to the sending socket.
Ingress BPF runs as part of netif_rx(), pushes a valid v6 hdr
and changes skb->protocol to v6. We enter ip6_rcv_core which
tries to use skb_dst(). But the dst is still an IPv4 one left
after IPv4 mcast output.
Clear the dst in all BPF helpers which change the protocol.
Try to preserve metadata dsts, those may carry non-routing
metadata. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: mtk-pmic-keys - fix possible null pointer dereference
In mtk_pmic_keys_probe, the regs parameter is only set if the button is
parsed in the device tree. However, on hardware where the button is left
floating, that node will most likely be removed not to enable that
input. In that case the code will try to dereference a null pointer.
Let's use the regs struct instead as it is defined for all supported
platforms. Note that it is ok setting the key reg even if that latter is
disabled as the interrupt won't be enabled anyway. |
| In the Linux kernel, the following vulnerability has been resolved:
x86/mm: Eliminate window where TLB flushes may be inadvertently skipped
tl;dr: There is a window in the mm switching code where the new CR3 is
set and the CPU should be getting TLB flushes for the new mm. But
should_flush_tlb() has a bug and suppresses the flush. Fix it by
widening the window where should_flush_tlb() sends an IPI.
Long Version:
=== History ===
There were a few things leading up to this.
First, updating mm_cpumask() was observed to be too expensive, so it was
made lazier. But being lazy caused too many unnecessary IPIs to CPUs
due to the now-lazy mm_cpumask(). So code was added to cull
mm_cpumask() periodically[2]. But that culling was a bit too aggressive
and skipped sending TLB flushes to CPUs that need them. So here we are
again.
=== Problem ===
The too-aggressive code in should_flush_tlb() strikes in this window:
// Turn on IPIs for this CPU/mm combination, but only
// if should_flush_tlb() agrees:
cpumask_set_cpu(cpu, mm_cpumask(next));
next_tlb_gen = atomic64_read(&next->context.tlb_gen);
choose_new_asid(next, next_tlb_gen, &new_asid, &need_flush);
load_new_mm_cr3(need_flush);
// ^ After 'need_flush' is set to false, IPIs *MUST*
// be sent to this CPU and not be ignored.
this_cpu_write(cpu_tlbstate.loaded_mm, next);
// ^ Not until this point does should_flush_tlb()
// become true!
should_flush_tlb() will suppress TLB flushes between load_new_mm_cr3()
and writing to 'loaded_mm', which is a window where they should not be
suppressed. Whoops.
=== Solution ===
Thankfully, the fuzzy "just about to write CR3" window is already marked
with loaded_mm==LOADED_MM_SWITCHING. Simply checking for that state in
should_flush_tlb() is sufficient to ensure that the CPU is targeted with
an IPI.
This will cause more TLB flush IPIs. But the window is relatively small
and I do not expect this to cause any kind of measurable performance
impact.
Update the comment where LOADED_MM_SWITCHING is written since it grew
yet another user.
Peter Z also raised a concern that should_flush_tlb() might not observe
'loaded_mm' and 'is_lazy' in the same order that switch_mm_irqs_off()
writes them. Add a barrier to ensure that they are observed in the
order they are written. |
| In the Linux kernel, the following vulnerability has been resolved:
net: ethernet: mtk-star-emac: fix spinlock recursion issues on rx/tx poll
Use spin_lock_irqsave and spin_unlock_irqrestore instead of spin_lock
and spin_unlock in mtk_star_emac driver to avoid spinlock recursion
occurrence that can happen when enabling the DMA interrupts again in
rx/tx poll.
```
BUG: spinlock recursion on CPU#0, swapper/0/0
lock: 0xffff00000db9cf20, .magic: dead4ead, .owner: swapper/0/0,
.owner_cpu: 0
CPU: 0 UID: 0 PID: 0 Comm: swapper/0 Not tainted
6.15.0-rc2-next-20250417-00001-gf6a27738686c-dirty #28 PREEMPT
Hardware name: MediaTek MT8365 Open Platform EVK (DT)
Call trace:
show_stack+0x18/0x24 (C)
dump_stack_lvl+0x60/0x80
dump_stack+0x18/0x24
spin_dump+0x78/0x88
do_raw_spin_lock+0x11c/0x120
_raw_spin_lock+0x20/0x2c
mtk_star_handle_irq+0xc0/0x22c [mtk_star_emac]
__handle_irq_event_percpu+0x48/0x140
handle_irq_event+0x4c/0xb0
handle_fasteoi_irq+0xa0/0x1bc
handle_irq_desc+0x34/0x58
generic_handle_domain_irq+0x1c/0x28
gic_handle_irq+0x4c/0x120
do_interrupt_handler+0x50/0x84
el1_interrupt+0x34/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
regmap_mmio_read32le+0xc/0x20 (P)
_regmap_bus_reg_read+0x6c/0xac
_regmap_read+0x60/0xdc
regmap_read+0x4c/0x80
mtk_star_rx_poll+0x2f4/0x39c [mtk_star_emac]
__napi_poll+0x38/0x188
net_rx_action+0x164/0x2c0
handle_softirqs+0x100/0x244
__do_softirq+0x14/0x20
____do_softirq+0x10/0x20
call_on_irq_stack+0x24/0x64
do_softirq_own_stack+0x1c/0x40
__irq_exit_rcu+0xd4/0x10c
irq_exit_rcu+0x10/0x1c
el1_interrupt+0x38/0x68
el1h_64_irq_handler+0x18/0x24
el1h_64_irq+0x6c/0x70
cpuidle_enter_state+0xac/0x320 (P)
cpuidle_enter+0x38/0x50
do_idle+0x1e4/0x260
cpu_startup_entry+0x34/0x3c
rest_init+0xdc/0xe0
console_on_rootfs+0x0/0x6c
__primary_switched+0x88/0x90
``` |
| In the Linux kernel, the following vulnerability has been resolved:
net: lan743x: Fix memleak issue when GSO enabled
Always map the `skb` to the LS descriptor. Previously skb was
mapped to EXT descriptor when the number of fragments is zero with
GSO enabled. Mapping the skb to EXT descriptor prevents it from
being freed, leading to a memory leak |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix OOB read when checking dotdot dir
Mounting a corrupted filesystem with directory which contains '.' dir
entry with rec_len == block size results in out-of-bounds read (later
on, when the corrupted directory is removed).
ext4_empty_dir() assumes every ext4 directory contains at least '.'
and '..' as directory entries in the first data block. It first loads
the '.' dir entry, performs sanity checks by calling ext4_check_dir_entry()
and then uses its rec_len member to compute the location of '..' dir
entry (in ext4_next_entry). It assumes the '..' dir entry fits into the
same data block.
If the rec_len of '.' is precisely one block (4KB), it slips through the
sanity checks (it is considered the last directory entry in the data
block) and leaves "struct ext4_dir_entry_2 *de" point exactly past the
memory slot allocated to the data block. The following call to
ext4_check_dir_entry() on new value of de then dereferences this pointer
which results in out-of-bounds mem access.
Fix this by extending __ext4_check_dir_entry() to check for '.' dir
entries that reach the end of data block. Make sure to ignore the phony
dir entries for checksum (by checking name_len for non-zero).
Note: This is reported by KASAN as use-after-free in case another
structure was recently freed from the slot past the bound, but it is
really an OOB read.
This issue was found by syzkaller tool.
Call Trace:
[ 38.594108] BUG: KASAN: slab-use-after-free in __ext4_check_dir_entry+0x67e/0x710
[ 38.594649] Read of size 2 at addr ffff88802b41a004 by task syz-executor/5375
[ 38.595158]
[ 38.595288] CPU: 0 UID: 0 PID: 5375 Comm: syz-executor Not tainted 6.14.0-rc7 #1
[ 38.595298] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
[ 38.595304] Call Trace:
[ 38.595308] <TASK>
[ 38.595311] dump_stack_lvl+0xa7/0xd0
[ 38.595325] print_address_description.constprop.0+0x2c/0x3f0
[ 38.595339] ? __ext4_check_dir_entry+0x67e/0x710
[ 38.595349] print_report+0xaa/0x250
[ 38.595359] ? __ext4_check_dir_entry+0x67e/0x710
[ 38.595368] ? kasan_addr_to_slab+0x9/0x90
[ 38.595378] kasan_report+0xab/0xe0
[ 38.595389] ? __ext4_check_dir_entry+0x67e/0x710
[ 38.595400] __ext4_check_dir_entry+0x67e/0x710
[ 38.595410] ext4_empty_dir+0x465/0x990
[ 38.595421] ? __pfx_ext4_empty_dir+0x10/0x10
[ 38.595432] ext4_rmdir.part.0+0x29a/0xd10
[ 38.595441] ? __dquot_initialize+0x2a7/0xbf0
[ 38.595455] ? __pfx_ext4_rmdir.part.0+0x10/0x10
[ 38.595464] ? __pfx___dquot_initialize+0x10/0x10
[ 38.595478] ? down_write+0xdb/0x140
[ 38.595487] ? __pfx_down_write+0x10/0x10
[ 38.595497] ext4_rmdir+0xee/0x140
[ 38.595506] vfs_rmdir+0x209/0x670
[ 38.595517] ? lookup_one_qstr_excl+0x3b/0x190
[ 38.595529] do_rmdir+0x363/0x3c0
[ 38.595537] ? __pfx_do_rmdir+0x10/0x10
[ 38.595544] ? strncpy_from_user+0x1ff/0x2e0
[ 38.595561] __x64_sys_unlinkat+0xf0/0x130
[ 38.595570] do_syscall_64+0x5b/0x180
[ 38.595583] entry_SYSCALL_64_after_hwframe+0x76/0x7e |
| In the Linux kernel, the following vulnerability has been resolved:
thermal: int340x: Add NULL check for adev
Not all devices have an ACPI companion fwnode, so adev might be NULL.
This is similar to the commit cd2fd6eab480
("platform/x86: int3472: Check for adev == NULL").
Add a check for adev not being set and return -ENODEV in that case to
avoid a possible NULL pointer deref in int3402_thermal_probe().
Note, under the same directory, int3400_thermal_probe() has such a
check.
[ rjw: Subject edit, added Fixes: ] |
| In the Linux kernel, the following vulnerability has been resolved:
net: Remove RTNL dance for SIOCBRADDIF and SIOCBRDELIF.
SIOCBRDELIF is passed to dev_ioctl() first and later forwarded to
br_ioctl_call(), which causes unnecessary RTNL dance and the splat
below [0] under RTNL pressure.
Let's say Thread A is trying to detach a device from a bridge and
Thread B is trying to remove the bridge.
In dev_ioctl(), Thread A bumps the bridge device's refcnt by
netdev_hold() and releases RTNL because the following br_ioctl_call()
also re-acquires RTNL.
In the race window, Thread B could acquire RTNL and try to remove
the bridge device. Then, rtnl_unlock() by Thread B will release RTNL
and wait for netdev_put() by Thread A.
Thread A, however, must hold RTNL after the unlock in dev_ifsioc(),
which may take long under RTNL pressure, resulting in the splat by
Thread B.
Thread A (SIOCBRDELIF) Thread B (SIOCBRDELBR)
---------------------- ----------------------
sock_ioctl sock_ioctl
`- sock_do_ioctl `- br_ioctl_call
`- dev_ioctl `- br_ioctl_stub
|- rtnl_lock |
|- dev_ifsioc '
' |- dev = __dev_get_by_name(...)
|- netdev_hold(dev, ...) .
/ |- rtnl_unlock ------. |
| |- br_ioctl_call `---> |- rtnl_lock
Race | | `- br_ioctl_stub |- br_del_bridge
Window | | | |- dev = __dev_get_by_name(...)
| | | May take long | `- br_dev_delete(dev, ...)
| | | under RTNL pressure | `- unregister_netdevice_queue(dev, ...)
| | | | `- rtnl_unlock
\ | |- rtnl_lock <-' `- netdev_run_todo
| |- ... `- netdev_run_todo
| `- rtnl_unlock |- __rtnl_unlock
| |- netdev_wait_allrefs_any
|- netdev_put(dev, ...) <----------------'
Wait refcnt decrement
and log splat below
To avoid blocking SIOCBRDELBR unnecessarily, let's not call
dev_ioctl() for SIOCBRADDIF and SIOCBRDELIF.
In the dev_ioctl() path, we do the following:
1. Copy struct ifreq by get_user_ifreq in sock_do_ioctl()
2. Check CAP_NET_ADMIN in dev_ioctl()
3. Call dev_load() in dev_ioctl()
4. Fetch the master dev from ifr.ifr_name in dev_ifsioc()
3. can be done by request_module() in br_ioctl_call(), so we move
1., 2., and 4. to br_ioctl_stub().
Note that 2. is also checked later in add_del_if(), but it's better
performed before RTNL.
SIOCBRADDIF and SIOCBRDELIF have been processed in dev_ioctl() since
the pre-git era, and there seems to be no specific reason to process
them there.
[0]:
unregister_netdevice: waiting for wpan3 to become free. Usage count = 2
ref_tracker: wpan3@ffff8880662d8608 has 1/1 users at
__netdev_tracker_alloc include/linux/netdevice.h:4282 [inline]
netdev_hold include/linux/netdevice.h:4311 [inline]
dev_ifsioc+0xc6a/0x1160 net/core/dev_ioctl.c:624
dev_ioctl+0x255/0x10c0 net/core/dev_ioctl.c:826
sock_do_ioctl+0x1ca/0x260 net/socket.c:1213
sock_ioctl+0x23a/0x6c0 net/socket.c:1318
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:906 [inline]
__se_sys_ioctl fs/ioctl.c:892 [inline]
__x64_sys_ioctl+0x1a4/0x210 fs/ioctl.c:892
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcb/0x250 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: sja1105: fix kasan out-of-bounds warning in sja1105_table_delete_entry()
There are actually 2 problems:
- deleting the last element doesn't require the memmove of elements
[i + 1, end) over it. Actually, element i+1 is out of bounds.
- The memmove itself should move size - i - 1 elements, because the last
element is out of bounds.
The out-of-bounds element still remains out of bounds after being
accessed, so the problem is only that we touch it, not that it becomes
in active use. But I suppose it can lead to issues if the out-of-bounds
element is part of an unmapped page. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: brcmstb: Fix error path after a call to regulator_bulk_get()
If the regulator_bulk_get() returns an error and no regulators
are created, we need to set their number to zero.
If we don't do this and the PCIe link up fails, a call to the
regulator_bulk_free() will result in a kernel panic.
While at it, print the error value, as we cannot return an error
upwards as the kernel will WARN() on an error from add_bus().
[kwilczynski: commit log, use comma in the message to match style with
other similar messages] |
