| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx: mark I2C adapter when hardware is powered down
On some i.MX platforms, certain I2C client drivers keep a periodic
workqueue which continues to trigger I2C transfers.
During system suspend/resume, there exists a time window between:
- suspend_noirq and the system entering suspend
- the system starting to resume and resume_noirq
In this window, the I2C controller resources such as clock and pinctrl
may already be disabled or not yet restored.
If a workqueue triggers an I2C transfer in this period, the driver
attempts to access I2C registers while the hardware resources are
unavailable, which may lead to system hang.
Mark the I2C adapter as suspended during noirq suspend and block new
transfers until resume, ensuring that I2C transfers are only issued
when hardware resources are available. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: pch: use raw_spinlock_t for the register lock
pch_irq_type() is registered as the irq_chip .irq_set_type callback and
takes chip->spinlock with spin_lock_irqsave(). This callback is reached
from __setup_irq() -> __irq_set_trigger() -> chip->irq_set_type() while
the caller holds desc->lock, a raw_spinlock_t, with hardirqs disabled.
That context is not sleepable, but on PREEMPT_RT a regular spinlock_t is
an rtmutex-backed sleeping lock, so acquiring it there is invalid.
This was confirmed on a PREEMPT_RT kernel with lockdep
(PROVE_RAW_LOCK_NESTING and DEBUG_ATOMIC_SLEEP). A grounded PoC mirrored
pch_irq_type()'s locking and drove it through the real genirq carrier
irq_set_irq_type() -> __irq_set_trigger() -> chip->irq_set_type(), i.e.
the same __irq_set_trigger() edge that __setup_irq() takes for a
requested IRQ. With the original spin_lock_irqsave() edge lockdep
reported an invalid wait context, immediately followed by:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 95, name: insmod
hardirqs last disabled at (3784): _raw_spin_lock_irqsave+0x4f/0x60
rt_spin_lock+0x3a/0x1c0
repro_irq_set_type+0x64/0xa0 [pch_repro]
__irq_set_trigger+0x69/0x140
irq_set_irq_type+0x78/0xd0
Switching the mirrored lock to raw_spinlock_t made both splats go away.
Convert the register lock to raw_spinlock_t. The same lock also
serializes the GPIO direction/value callbacks and the suspend/resume
register save/restore, but all of those critical sections only perform
MMIO register accesses (ioread32()/iowrite32()) and
irq_set_handler_locked(); none of them contain sleepable operations.
Keeping this register lock non-sleeping is therefore appropriate for the
irqchip callbacks and does not change the GPIO-side locking contract.
This is the same class of issue and fix as recently addressed for other
GPIO controllers, e.g. commit 286533cb14a3 ("gpio: sch: use raw_spinlock_t
in the irq startup path") and commit 90f0109019e6 ("gpio: eic-sprd: use
raw_spinlock_t in the irq startup path"). |
| In the Linux kernel, the following vulnerability has been resolved:
uprobes: Fix NULL pointer dereference in hprobe_expire()
Forking a task that has a pending uretprobe can oops the kernel with a
NULL pointer dereference in the clone() path:
BUG: kernel NULL pointer dereference, address: 0000000000000018
Oops: 0002 [#1] SMP NOPTI
RIP: 0010:hprobe_expire
CR2: 0000000000000018
Call Trace:
uprobe_copy_process
copy_process
kernel_clone
__x64_sys_clone
do_syscall_64
entry_SYSCALL_64_after_hwframe
This was found on real hosts on Meta fleet.
I've got the impression that this is what is happening:
CPU 1 CPU 2 (traced task)
----- -------------------
hit uprobe, prepare_uretprobe():
hprobe LEASED, refcount >= 1
uprobe_unregister()
put_uprobe(): refcount -> 0
fork() -> dup_utask()
hprobe_expire(hprobe, true)
try_get_uprobe() -> NULL
get_uprobe(NULL) <-- Oops
Only take the extra reference when the uprobe is non-NULL; a NULL means
it is gone and is the correct value to return. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Clamp frame size in implicit-feedback mode
snd_usb_handle_sync_urb() scales received sync packet sizes by the sender's
stride and stores the result directly in out_packet->packet_size[i]. If a
connected USB device sends an oversized sync packet, this frame count can
exceed ep->maxframesize.
The un-clamped frame count then propagates to the playback endpoint queue,
potentially driving packet transfers beyond the endpoint's hardware frame
limits.
Cap the calculated frame count against ep->maxframesize in
snd_usb_handle_sync_urb() to prevent oversized packets from entering the
playback queue. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: ump: fix double free of out_cvts on rawmidi error
snd_ump_attach_legacy_rawmidi() allocates the legacy conversion array
ump->out_cvts and, on the snd_rawmidi_new() error path, frees it with
kfree() but leaves ump->out_cvts pointing at the freed memory. When the
endpoint is later torn down, snd_ump_endpoint_free() frees ump->out_cvts
a second time, resulting in a double free.
The host snd-usb-audio driver attaches the legacy rawmidi for any USB
MIDI 2.0 (UMP) device, so a device that makes snd_rawmidi_new() fail
reaches this path on enumeration.
Clear ump->out_cvts after freeing it on the error path so it is not
freed again during teardown.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
media: uvcvideo: Fix deadlock if uvc_status_stop is called from async_ctrl.work
If a UVC camera has an asynchronous control, uvc_status_stop may be
called from async_ctrl.work:
uvc_ctrl_status_event_work()
uvc_ctrl_status_event()
uvc_ctrl_clear_handle()
uvc_pm_put()
uvc_status_put()
uvc_status_stop()
cancel_work_sync()
This will cause a deadlock, since cancel_work_sync will wait for
uvc_ctrl_status_event_work to complete before returning.
Fix this by returning early from uvc_status_stop if we are currently in
the work function. flush_status now remains false until uvc_status_start
is called again, ensuring that uvc_ctrl_status_event_work won't resubmit
the URB. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mpi3mr: Fix potential deadlock in mpi3mr_fault_uevent_emit
mpi3mr_fault_uevent_emit() runs from the fault watchdog and reset paths
where host I/O may already be blocked. GFP_KERNEL allocations here, both
the local kzalloc_obj() and the ones inside kobject_uevent_env() itself,
can trigger reclaim that waits on that blocked I/O and deadlock.
Use memalloc_noio_save()/restore() to cover the whole call instead of
just the local allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix use-after-free in __close_file_table_ids()
A ksmbd_file can remain alive after logical close while another session
holds a temporary reference obtained through ksmbd_lookup_fd_inode().
ksmbd_close_fd() currently marks the file closed and drops the idr-owned
reference, but leaves the pointer published in the closing session's idr
until the final reference is dropped.
If the foreign holder performs the final ksmbd_fd_put(), __put_fd_final()
supplies the foreign session's file table to __ksmbd_close_fd(). The object
is then freed without being removed from its owner's idr, and the owner
session later dereferences the stale pointer during file-table teardown.
Remove the volatile id from the owner's idr while ksmbd_close_fd() still
holds that table's lock, and clear volatile_id before dropping
the idr-owned reference. A later foreign final put then only performs
physical destruction and cannot remove the object from the wrong table. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel: Validate length before parsing diagnostics TLV
btintel_diagnostics() accesses tlv->val[0] without first validating
that the diagnostics VSE is long enough to contain that field, so
may cause reading data beyond the received frame.
Fix by validating the length before access. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: lock sk in iso_sock_getname
Accessing iso_pi(sk)->conn requires lock_sock, which is not held here.
Fix by adding the lock/release. |
| In the Linux kernel, the following vulnerability has been resolved:
rds: tcp: hold the RCU lock across ipv6_chk_addr() in rds_tcp_laddr_check()
rds_tcp_laddr_check() looks up a scoped IPv6 interface with
dev_get_by_index_rcu(), drops the RCU read-side lock, and only then
passes the bare struct net_device * into ipv6_chk_addr().
dev_get_by_index_rcu() only keeps the device alive within the same RCU
read-side section. After rcu_read_unlock(), a concurrent RTM_DELLINK can
free the net_device; ipv6_chk_addr() then dereferences the stale pointer
in __ipv6_chk_addr_and_flags() (e.g. l3mdev_master_dev_rcu(dev)), reading
freed memory.
Keep the RCU read-side lock held across the ipv6_chk_addr() call instead
of dropping it right after the lookup, so the device cannot be freed
while it is in use.
BUG: KASAN: slab-use-after-free in __ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
Read of size 8 at addr ffff8880106ec000 by task exploit/153
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
__ipv6_chk_addr_and_flags (... net/ipv6/addrconf.c:1998)
ipv6_chk_addr (net/ipv6/addrconf.c:2031 net/ipv6/addrconf.c:1972)
rds_tcp_laddr_check (net/rds/tcp.c:370)
rds_bind (net/rds/bind.c:248)
__sys_bind (net/socket.c:1920)
__x64_sys_bind (net/socket.c:1956)
do_syscall_64 (arch/x86/entry/syscall_64.c:63)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:121) |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nct6775-core) Fix number of temperature registers for NCT6116
Unlike NCT6106, NCT6116 only has three temperature registers, and with
it only three temperature source and temperature source configuration
registers. The register addresses match those of NCT6106 and can be
re-used.
The code used a separate array to list the temperature source registers
for NCT6116, but used the size of the NCT6106 register array to set
the number of registers. The NCT6106 register array provides six addresses,
while the temperature source register array for NCT6116 only provides three
addresses. This causes a KASAN report.
BUG: KASAN: global-out-of-bounds in nct6775_probe+0x936/0x46f0 [nct6775]
Read of size 2 at addr ffffffffc19561a6 by task modprobe/954
...
Call Trace:
dump_stack+0x7d/0xa7
print_address_description.constprop.0+0x1c/0x220
? __kasan_kmalloc.constprop.0+0xc9/0xd0
? __kmalloc_node_track_caller+0x194/0x5b0
? nct6775_probe+0x936/0x46f0 [nct6775]
? nct6775_probe+0x936/0x46f0 [nct6775]
...
Fix the problem by hard-coding the number of temperature and temperature
configuration registers to three for NCT6116. Drop the unnecessary
NCT6116_REG_TEMP_SOURCE array and re-use NCT6106_REG_TEMP_SOURCE. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nzxt-smart2) DMA-align output buffer
Sashiko reports:
When send_output_report() calls hid_hw_output_report(), the underlying USB
HID core calls usb_interrupt_msg() which maps this buffer directly for DMA.
When the DMA mapping flushes or invalidates the cacheline, it will corrupt
the adjacent variables (mutex, update_interval) that were modified
concurrently by the CPU. This causes memory corruption due to cacheline
sharing on non-coherent CPU architectures (such as ARM or MIPS). The DMA
API debugging tool (CONFIG_DMA_API_DEBUG) will trigger runtime warnings
for this violation.
Any operation that triggers send_output_report() (like setting a fan speed
or updating the interval) causes the USB DMA mapping. On systems with
non-coherent caches, this structural bug causes immediate and deterministic
memory corruption.
Align the output buffer to ARCH_DMA_MINALIGN to fix the problem. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Update x2APIC MSR intercepts if AVIC is inhibited while L2 is active
Always update x2APIC MSR intercepts for L1 when AVIC is deactivated, even
if L2 is active and KVM is using a separate MSR bitmap to run L2. If AVIC
is fully enabled prior to running L2, and is then inhibited while L2 is
active (for a VM-scoped inhibit), then KVM will run L1 with AVIC disabled,
but with x2APIC MSR intercepts disabled, i.e. will allow L1 to read most of
the host's APIC state, send arbitrary interrupts, change task priority, and
ultimately trivially DoS the host.
E.g. sending a self-IPI in L1 on HYPERV_REENLIGHTENMENT_VECTOR, 0xee, with
CONFIG_HYPERV=n in the host kernel as a "safe" PoC, yields:
Spurious interrupt (vector 0xee) on CPU#425. Acked
And hacking KVM to abuse kvm_set_posted_intr_wakeup_handler() to register a
handler and WARN on POSTED_INTR_WAKEUP_VECTOR yields:
------------[ cut here ]------------
WARNING: arch/x86/kvm/svm/svm.c:5594 at pi_wakeup_handler+0x9/0x10 [kvm_amd], CPU#156: nested_x2apic_t/316940
CPU: 156 UID: 0 PID: 316940 Comm: nested_x2apic_t Tainted: G S U
Tainted: [S]=CPU_OUT_OF_SPEC, [U]=USER
Hardware name: Google Astoria-Turin/astoria, BIOS 0.20260209.0-0 02/09/2026
RIP: 0010:pi_wakeup_handler+0x9/0x10 [kvm_amd]
Call Trace:
<IRQ>
sysvec_kvm_posted_intr_wakeup_ipi+0x64/0x80
</IRQ>
<TASK>
asm_sysvec_kvm_posted_intr_wakeup_ipi+0x1a/0x20
RIP: 0010:vcpu_run+0x1430/0x1e40 [kvm]
kvm_arch_vcpu_ioctl_run+0x2c1/0x600 [kvm]
kvm_vcpu_ioctl+0x580/0x6b0 [kvm]
__se_sys_ioctl+0x6d/0xb0
do_syscall_64+0x10a/0x480
entry_SYSCALL_64_after_hwframe+0x4b/0x53
RIP: 0033:0x46ff4b
</TASK>
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: pci: Reject adapter interrupt forwarding if already enabled
The MPCIFC instruction doesn't allow registering adapter interrupts without
first unregistering. So reject any request to enable interrupt forwarding
if its already enabled for the zPCI device. This also fixes overwriting and
thus leaking resources when the ioctl is called multiple times for the same
device. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: use the subframe length when parsing A-MSDU TDLS frames
mwifiex_11n_dispatch_amsdu_pkt() splits an A-MSDU with
ieee80211_amsdu_to_8023s() and walks the resulting subframes. For each
subframe it passes the subframe data pointer to
mwifiex_process_tdls_action_frame(), but pairs it with skb->len, the
length of the A-MSDU parent, instead of rx_skb->len:
rx_skb = __skb_dequeue(&list);
rx_hdr = (struct rx_packet_hdr *)rx_skb->data;
if (ISSUPP_TDLS_ENABLED(priv->adapter->fw_cap_info) &&
ntohs(rx_hdr->eth803_hdr.h_proto) == ETH_P_TDLS) {
mwifiex_process_tdls_action_frame(priv, (u8 *)rx_hdr,
skb->len);
}
The parent is not a valid description of that buffer, and may not be
valid memory at all. ieee80211_amsdu_to_8023s() ends with
if (!reuse_skb)
dev_kfree_skb(skb);
and it only sets reuse_skb when the parent is linear, is not a
head_frag, and is being consumed as the *last* subframe. So when the
parent does not qualify for reuse it has already been freed, and the
read of skb->len is a use-after-free. When it is reused, skb->len is
the length of the last subframe, applied to every earlier subframe,
which over-states the buffer whenever an earlier subframe is shorter.
The callee cannot absorb a wrong length, because it derives its own
ceiling from the value it is given. Each frame type computes
ies_len = len - sizeof(struct ethhdr) - TDLS_*_FIX_LEN;
and the element walk is then bounded entirely against that ceiling,
for (end = pos + ies_len; pos + 1 < end; pos += 2 + pos[1]) {
u8 ie_len = pos[1];
if (pos + 2 + ie_len > end)
break;
so a too-large len moves end past the end of the subframe and the walk
reads and copies beyond it. The A-MSDU layout is chosen by the sender,
which makes the difference between the last subframe and a shorter
earlier one remotely selectable. Reaching this requires TDLS support in
firmware and the TDLS ethertype on the subframe.
The other caller, mwifiex_process_rx_packet(), is correct: it passes a
pointer and a length that describe the same region of the RX buffer.
Pass rx_skb->len, the length of the subframe actually being parsed. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/huge_memory: unlock i_mmap_rwsem before releasing after-split folios
__folio_split() keeps dereferencing the mapping after the split:
shmem_uncharge(mapping->host) and remap_page() while the folios are still
frozen/locked, and i_mmap_unlock_read(mapping) at the very end, after the
after-split folios have been unlocked and freed.
Nothing holds an inode reference across that. The split relies on @folio
-- which the beyond-EOF drop loop never removes, as it starts at
folio_next(folio) -- staying locked and in the page cache to hold off
eviction. But the unlock loop unlocks @folio before i_mmap_unlock_read()
runs. If the caller's @lock_at is a tail beyond EOF, as memory_failure()
passes when splitting a poisoned tail of a shmem THP that reaches past
i_size during truncation, it too is gone from the page cache; so once
@folio is unlocked no locked, in-cache folio pins the inode, and a
concurrent final iput() can evict and RCU-free it before
i_mmap_unlock_read() touches i_mmap_rwsem:
BUG: KASAN: slab-use-after-free in __up_read+0x634/0x790
i_mmap_unlock_read include/linux/fs.h:537 [inline]
__folio_split+0x732/0x1640 mm/huge_memory.c:4100
try_to_split_thp_page+0xab/0x390 mm/memory-failure.c:1675
memory_failure+0x1394/0x26e0 mm/memory-failure.c:2470
Freed by task 4601:
shmem_free_in_core_inode+0x54/0xb0 mm/shmem.c:5177
evict+0x57f/0xac0 fs/inode.c:870
Do every mapping dereference while @folio still pins the inode: drop
i_mmap_rwsem right after remap_page(), before the loop that unlocks and
frees the after-split folios, and clear @mapping so the exit path does not
unlock it again. shmem_uncharge() and remap_page() already run before
that point, so after this nothing past the unlock loop touches the inode
or the mapping.
This is now a rule the split depends on, alongside keeping @folio frozen
until the page cache is updated: no inode or mapping dereference once the
after-split folios start being unlocked. |
| In the Linux kernel, the following vulnerability has been resolved:
um: vector: fix use-after-free in vector_mmsg_rx()
When vector_mmsg_rx() discards a packet whose overlay header fails
verify_header(), it frees the skb and continues the loop:
if (header_check < 0) {
dev_kfree_skb_irq(skb);
vp->estats.rx_encaps_errors++;
continue;
}
The normal and short-packet paths fall through to the bottom of the
loop body, which clears the consumed slot and advances the cursors:
(*skbuff_vector) = NULL;
mmsg_vector++;
skbuff_vector++;
The verify_header() < 0 path skips that via continue, so the freed skb
is left in skbuff_vector[] and the cursors do not advance. The next
iteration reads the same slot, gets the freed skb, and frees it again,
producing a refcount underflow / use-after-free in the RX path.
Discard the slot the same way the other paths do before continuing.
Only transports whose verify_header() can return negative are affected:
GRE and L2TPv3 do so on a cookie/session-id mismatch (raw/tap do not),
so any peer on such a transport can trigger it without authentication. |
| In the Linux kernel, the following vulnerability has been resolved:
ublk: reset kernel-owned dev_info fields in ublk_ctrl_add_dev()
ublk_ctrl_add_dev() memcpy()s the userspace ublksrv_ctrl_dev_info into
ub->dev_info and then fixes up the fields the driver owns, but misses
->state and ->ublksrv_pid.
A device added with ->state = UBLK_S_DEV_LIVE passes the
"->state != UBLK_S_DEV_DEAD" test that ublk_stop_dev_unlocked() uses as its
proxy for "a disk is attached", while ->ub_disk is still NULL, so DEL_DEV
right after ADD_DEV oopses in del_gendisk(). UBLK_S_DEV_QUIESCED plus
UBLK_F_USER_RECOVERY dies one step earlier, in ublk_force_abort_dev(). A
poisoned ->state also gets START_USER_RECOVERY and the char device
read/write path onto a device that was never started, and wedges START_DEV
at -EEXIST. A poisoned ->ublksrv_pid just makes GET_DEV_INFO report an
unrelated task as the ublk server.
Reset both after the memcpy(), as ublk_detach_disk() does. Userspace only
ever reads these back, so correcting them silently breaks nothing.
ADD_DEV has copied ->state in unsanitized since ublk was merged, but back
then it was harmless: the gendisk was allocated during ADD_DEV, and both
teardown and the START_DEV -EEXIST check keyed off disk_live() rather than
->state. The oops became reachable once the disk allocation moved to
START_DEV and those checks switched to ->state. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libsas: Fix HA resume deadlock and hisi_sas disk-wake race
Commit fbefe22811c3 ("scsi: libsas: Don't always drain event workqueue
for HA resume") introduced sas_resume_ha_no_sync() to avoid a deadlock:
the PHYE_RESUME_TIMEOUT handler, running on the HA event workqueue,
calls sas_deform_port() -> sas_destruct_devices(), which removes SCSI
devices and waits for the host to become runtime-active. But the host
cannot resume until sas_resume_ha() -> sas_drain_work() returns, and the
drain is blocked on that very handler.
However skipping the drain reintroduces a race: hisi_sas returns from
resume before all PHY UP work and libsas discovery work finish. The
controller may then autosuspend while disks are still waking up. The
disks issue IO to a suspended controller, the IO fails, and the disks
get disabled.
Fix the deadlock at its source by moving the PHYE_RESUME_TIMEOUT
notification to after sas_drain_work(). By then the host resume is about
to complete, so device removal through device_link no longer blocks on
the resume and the cycle is broken.
With the deadlock gone, restore sas_resume_ha() (the draining variant)
in hisi_sas and remove sas_resume_ha_no_sync().
The reorder is safe for the other libsas consumers (isci, pm8001,
aic94xx, mvsas). During suspend, sas_suspend_devices() calls
sas_notify_lldd_dev_gone() for each device, which sets dev->lldd_dev to
NULL. When scsi_unblock_requests re-enables I/O in resume, any I/O to a
timed-out phy's disk is immediately rejected by the LLDD before reaching
hardware: isci returns SAS_DEVICE_UNKNOWN (mapped to DID_BAD_TARGET),
and pm8001 returns SAS_PHY_DOWN (mapped to DID_NO_CONNECT). Both
complete directly via scsi_done() without entering SCSI EH. This is
identical in both the old and new ordering since lldd_dev_gone runs
during suspend, before resume. The reorder only affects when the
PHYE_RESUME_TIMEOUT handler runs (synchronized by sas_drain_work()
vs. asynchronous after resume returns), not whether I/O can reach the
device. aic94xx and mvsas do not register any PM ops and never reach
this code path. |
