| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
media: vivid: check for vb2_is_busy() when toggling caps
The vivid_update_format_cap/out() functions must only be called if the
capture/output queue are not busy. But for the controls that select
the CROP/COMPOSE/SCALE capability that is not checked.
Only when streaming starts will they be set to 'grabbed' and it is
impossible to change the control, but between REQBUFS and STREAMON you
are still allowed to set these controls. Since vivid_update_format_cap/out
will change the format, this can cause unexpected results.
Besides adding these checks, also add a WARN_ON in
vivid_update_format_cap/out() if the queue is busy.
I'm 90% certain that this is the cause of this syzbot bug:
https://syzkaller.appspot.com/bug?extid=dac8f5eaa46837e97b89
But since we never have reproducers, it is hard to be certain. In any case,
these checks are needed regardless. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wilc1000: validate assoc response length before subtracting header
wilc_parse_assoc_resp_info() computes the trailing IE length as
ies_len = buffer_len - sizeof(*res);
without first checking that buffer_len is at least sizeof(struct
wilc_assoc_resp) (6 bytes). buffer_len is the length reported for a
received association response (host_int_parse_assoc_resp_info() passes
hif_drv->assoc_resp / assoc_resp_info_len straight in) and must be
validated before the driver accesses the fixed header.
For a frame shorter than the 6-byte fixed header, the subtraction wraps.
For a four-byte response the result is truncated to a u16 ies_len of
65534, so kmemdup() then attempts to copy 65534 bytes starting at
buffer + sizeof(*res), beyond the valid association-response data
(CWE-125). A response shorter than four bytes can also cause an
out-of-bounds read of res->status_code at offsets 2 and 3.
Reject frames too short to hold the fixed header before touching the
header or computing ies_len. Also set the connection status to a failure
on this path: the caller falls through to a
"conn_info->status == WLAN_STATUS_SUCCESS" check after the parser
returns, so leaving the status untouched could let a malformed short
response be treated as a successful association. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7615: drop TXRX_NOTIFY on non-mmio buses
PKT_TYPE_TXRX_NOTIFY is an mmio-only event, but mt7615_rx_check() and
mt7615_queue_rx_skb() dispatch it to mt7615_mac_tx_free() on every bus.
mt7615_mac_tx_free() cleans the DMA tx queues with
mt76_queue_tx_cleanup(), which calls queue_ops->tx_cleanup(). Only the
mmio queue ops implement that callback; on the mt7663 USB and SDIO
buses it is NULL, so a TXRX_NOTIFY there calls a NULL pointer in the RX
worker. Same defect as the mt7921 and mt7925 patches in this series.
Drop the event on non-mmio buses via mt76_is_mmio(), as in
commit 5683e1488aa9 ("wifi: mt76: connac: do not check WED status for
non-mmio devices"). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: drop TXRX_NOTIFY on non-mmio buses
PKT_TYPE_TXRX_NOTIFY is an mmio-only event, but mt7921_rx_check() and
mt7921_queue_rx_skb() dispatch it to mt7921_mac_tx_free() on every bus.
mt7921_mac_tx_free() cleans the DMA tx queues with
mt76_queue_tx_cleanup(), which calls queue_ops->tx_cleanup(). Only the
mmio queue ops implement that callback; on USB and SDIO it is NULL, so
a TXRX_NOTIFY there calls a NULL pointer in the RX worker:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:0x0
Call Trace:
mt7921_mac_tx_free+0x64/0x310 [mt7921_common]
mt7921_rx_check+0x5f/0xf0 [mt7921_common]
mt76u_rx_worker+0x1b9/0x620 [mt76_usb]
Drop the event on non-mmio buses via mt76_is_mmio(), as in
commit 5683e1488aa9 ("wifi: mt76: connac: do not check WED status for
non-mmio devices"). |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: stratix10-svc: fix memory leaks and list corruption bugs
Fix a memory leak when gen_pool_alloc() fails by freeing pmem on the error
path. Switch pmem allocation from devm_kzalloc() to kzalloc() with
explicit kfree() in the free path to match its list-managed lifetime.
Remove the erroneous list_del(&svc_data_mem) which corrupted the list head
on failed lookups. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: comedi_parport: deal with premature interrupt
Syzbot reported a general protection fault in
`comedi_get_is_subdevice_running()`, which was called from the interrupt
handler `parport_interrupt()` in the "comedi_parport" driver, but it
does not currently have a C reproducer for the problem. It's
probably due to a premature interrupt for one of two reasons:
1. The driver sets up the interrupt handler before the comedi subdevices
used by the interrupt handler have been allocated, but does not
disable the interrupt in the parallel port's CTRL register first.
2. The driver uses a user-supplied I/O port base address which Syzbot
would have supplied, but it might not be backed by real parallel port
hardware.
Change the initialization order in the driver's comedi "attach" handler
(`parport_attach()`) so that the hardware registers are initialized
before the interrupt handler is requested. This should prevent
premature interrupts occurring for real hardware.
Also add a test to the interrupt handler to ensure the comedi device is
fully attached and return early if it isn't. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix mmiotrace possible NULL dereferencing of hiter->dev
If the mmio_pipe_open() fails to find a PCI device, the hiter->dev
will be assigned to NULL. The mmiotrace read() function dereferences the
hiter->dev if hiter exists.
Change the test of the read to not only check hiter being NULL, but also
the hiter->dev before dereferencing it. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix resource leak on mmiotrace trace_pipe close
The mmiotrace tracer was added May 12th 2008. At that time, resources
created in pipe_open() could not be freed because there was not
pipe_close function pointer of the tracer. The pipe_close function pointer
was added in December 7th, 2009, but the mmiotrace tracer was not updated.
mmio_pipe_open() allocates a header_iter and takes a pci_dev reference
when trace_pipe is opened. mmio_close() frees them, but it was only
wired to the tracer's .close callback.
tracing_release_pipe() invokes .pipe_close, not .close, when the
trace_pipe file is released. As a result, closing trace_pipe with the
mmiotrace tracer active leaked the header_iter allocation and left a
stale pci_dev reference.
Set .pipe_close to mmio_close, matching how function_graph wires both
callbacks to the same handler.
Note, if the trace_pipe is read to completion, it will clean up the
resources, but if one were to run:
# head -n 1 /sys/kernel/tracing/trace_pipe
VERSION 20070824
Over and over again, it would trigger a massive leak. |
| In the Linux kernel, the following vulnerability has been resolved:
binfmt_elf_fdpic: only honour the first PT_INTERP
The program header scan handles PT_INTERP from a switch nested in the
scan loop, so its break leaves the switch and not the loop. A binary
carrying more than one PT_INTERP runs the case again and overwrites both
interpreter_name and interpreter. The previous name allocation leaks and
so does the previous interpreter reference, along with the write denial
open_exec() took on it. The denial is never released, so the file stays
unwritable for as long as the system runs.
An unprivileged caller reaches this with a crafted binary and repeats it
at will. binfmt_elf stops at the first PT_INTERP. Do the same here.
The flaw dates back to the driver's introduction in the pre-git history
tree introduced in v2.6.11 by 91808d6ebe39 ("[PATCH] FRV: Add FDPIC ELF
binary format driver"). |
| In the Linux kernel, the following vulnerability has been resolved:
fscrypt: Avoid dynamic allocation in fscrypt_get_devices()
When a blk_crypto_key starts being used or is evicted, fs/crypto/ calls
fscrypt_get_devices() to get the filesystem's list of block devices,
then iterates over them and calls blk_crypto_config_supported(),
blk_crypto_start_using_key(), or blk_crypto_evict_key() on each one.
Currently, the block device pointers are placed in a dynamically
allocated array. This dynamic allocation is problematic because:
- It can fail, especially at the fscrypt_destroy_inline_crypt_key() call
site when it's invoked for inode eviction under direct reclaim.
- fscrypt_destroy_inline_crypt_key() doesn't handle the failure. It
just zeroizes and frees the blk_crypto_key without calling
blk_crypto_evict_key(). That causes a use-after-free.
For now, let's fix this in the straightforward and easily-backportable
way by switching to an on-stack array. Currently the fscrypt
multi-device functionality is used only by f2fs, which has a hardcoded
limit of 8 block devices. An on-stack array works fine for that.
(Of course, this solution won't scale up to large number of block
devices. For that we'd need a different solution, like moving the block
device iteration into the filesystem. Or in the case of btrfs, which
will only support blk-crypto-fallback, we should make it just call
blk-crypto-fallback directly, so the block devices won't be needed.) |
| In the Linux kernel, the following vulnerability has been resolved:
net/x25: fix use-after-free in x25_kill_by_neigh()
x25_kill_by_neigh() walks the global X.25 socket list looking for sockets
attached to a terminating neighbour. x25_list_lock protects list membership
while the lookup is in progress, but it does not pin a socket's lifetime
after the lock is dropped.
The function currently drops x25_list_lock before calling lock_sock(s). A
concurrent close can run x25_release(), remove the same socket from
x25_list, and drop the last socket reference in that window. The neighbour
teardown path can then lock or inspect a freed struct sock/struct x25_sock.
Take sock_hold(s) while x25_list_lock still proves that the list entry is
live, then drop the temporary reference after the socket has been locked,
rechecked, and released. Recheck x25_sk(s)->neighbour after lock_sock(),
because another path may have disconnected the socket before this path
acquired the socket lock. Restart the list walk after each disconnect
because the list lock was dropped and the previous iterator state may no
longer be valid.
A QEMU/KASAN run against origin/master reproduced a slab-use-after-free in
x25_kill_by_neigh(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: hip04: fix RX buffer leak on build_skb failure
When build_skb() fails in hip04_rx_poll(), the driver jumps to the
refill path without releasing the current RX buffer and its DMA mapping.
Installing a replacement buffer then overwrites the slot references and
leaks both resources.
Keep the current slot intact and return budget so NAPI retries the same
buffer. Also free a newly allocated RX fragment when dma_map_single()
fails.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
mctp: serial: handle zero-length frames to prevent rx buffer overflow
The MCTP serial receive state machine reads a frame length byte in
mctp_serial_push_header() case 2 and validates it upper-bound-only:
if (c > MCTP_SERIAL_FRAME_MTU) {
dev->rxstate = STATE_ERR;
} else {
dev->rxlen = c;
dev->rxpos = 0;
dev->rxstate = STATE_DATA;
...
}
A length of zero passes this check, so rxlen is set to 0 and the state
machine advances to STATE_DATA. In mctp_serial_push() STATE_DATA, the
incoming byte is stored and rxpos incremented before the terminator is
dev->rxbuf[dev->rxpos] = c;
dev->rxpos++;
dev->rxstate = STATE_DATA;
if (dev->rxpos == dev->rxlen) {
dev->rxpos = 0;
dev->rxstate = STATE_TRAILER;
}
With rxlen == 0 the "rxpos == rxlen" terminator can never fire (rxpos is
already 1 on the first data byte), so subsequent bytes are written past
the end of the fixed 74-byte rxbuf, which is the last member of the
netdev private area. Every following data byte is an attacker-controlled
1-byte out-of-bounds heap write, and the overflow continues until a
frame (0x7e) or escape byte resets the parser -- effectively unbounded.
Reaching this requires CAP_NET_ADMIN to attach the N_MCTP line
discipline and bring the resulting mctpserialN netdev up, after which
the bytes arrive via the tty receive path.
Route a zero-length frame straight to STATE_TRAILER instead of
STATE_DATA. The trailer/framing bytes are still consumed, and the frame
resolves to a zero-length skb that the MCTP core rejects; the parser
never enters STATE_DATA with rxlen == 0, so the out-of-bounds write can
no longer occur.
KASAN, on a frame of 0x7e 0x01 0x00 followed by data bytes (before this
change):
UBSAN: array-index-out-of-bounds in drivers/net/mctp/mctp-serial.c:370
index 74 is out of range for type 'u8 [74]'
BUG: KASAN: slab-out-of-bounds in mctp_serial_tty_receive_buf
Write of size 1 at addr ... by task kworker/u16:0
mctp_serial_tty_receive_buf
tty_ldisc_receive_buf
flush_to_ldisc
Allocated by task 152:
alloc_netdev_mqs
mctp_serial_open
v2: route zero-length frames to STATE_TRAILER instead of STATE_ERR so
the trailer/framing bytes are still consumed (Jeremy Kerr).
Found by 0sec automated security-research tooling (https://0sec.ai). |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: f_midi: cancel pending IN work before freeing the midi object
The f_midi driver embeds a work item (midi->work) whose handler,
f_midi_in_work(), dereferences the enclosing struct f_midi through
container_of(). This work is armed from two sites: f_midi_complete(),
on a normal IN-endpoint completion, and f_midi_in_trigger(), on an ALSA
rawmidi output-stream start.
Neither f_midi_disable() nor f_midi_unbind() cancels midi->work.
f_midi_disable() only disables the endpoints and drains the in_req_fifo;
it does not synchronize the work item, and the sound card is released
asynchronously to the final free of the midi object.
The midi object is reference-counted (midi->free_ref) and is freed in
f_midi_free() only once both the usb_function reference and the rawmidi
private_data reference have been dropped. In f_midi_unbind(),
f_midi_disable() runs before the sound card is released, so while the
USB endpoints are already disabled the rawmidi device is still usable by
an open substream. A concurrent userspace write on such a substream can
reach f_midi_in_trigger() and queue midi->work again after
f_midi_disable() has returned. A work item armed this way may still be
pending when the last reference drops and f_midi_free() proceeds to
kfree(midi), letting f_midi_in_work() dereference the struct after it
has been freed, a use-after-free.
For this reason cancelling midi->work in f_midi_disable() would not be
sufficient: the ALSA trigger path can rearm the work after disable()
returns. Cancelling at the refcount-zero free site is the boundary
after which neither arming source can survive, because by then both
references that keep the midi object alive have been dropped: the USB
endpoints are already disabled and the rawmidi device has been released.
Fix this by calling cancel_work_sync(&midi->work) in the refcount-zero
block of f_midi_free(), before the embedded work_struct is freed along
with the rest of the structure. opts->lock is a sleeping mutex, so
calling cancel_work_sync() under it is permitted, and the handler takes
midi->transmit_lock rather than opts->lock, so no self-deadlock can
occur while it waits for a running instance of the work to finish.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate compound request size before reading StructureSize2
When ksmbd validates a compound (chained) SMB2 request,
ksmbd_smb2_check_message() reads pdu->StructureSize2 without first
checking that the compound element is large enough to contain it.
StructureSize2 is a 2-byte field at offset 64
(__SMB2_HEADER_STRUCTURE_SIZE) from the start of each element.
The compound-walking logic only guarantees that a full 64-byte SMB2
header is present for the trailing element: when NextCommand is 0, len is
reduced to the number of bytes remaining after next_smb2_rcv_hdr_off. A
remote client can craft a compound request whose last element has exactly
64 bytes, so the 2-byte StructureSize2 read at offset 64 extends one byte
past the receive buffer, producing a slab-out-of-bounds read.
BUG: KASAN: slab-out-of-bounds in ksmbd_smb2_check_message (fs/smb/server/smb2misc.c:402)
Read of size 2 at addr ffff888012ae31ac by task kworker/0:1/14
The buggy address is located 172 bytes inside of allocated 173-byte region
Workqueue: ksmbd-io handle_ksmbd_work
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
ksmbd_smb2_check_message (fs/smb/server/smb2misc.c:402)
handle_ksmbd_work (fs/smb/server/server.c:119)
process_one_work (kernel/workqueue.c:3314)
worker_thread (kernel/workqueue.c:3397)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:158)
ret_from_fork_asm (arch/x86/entry/entry_64.S:245)
Reject any compound element that is too small to hold StructureSize2
before dereferencing it. |
| In the Linux kernel, the following vulnerability has been resolved:
gtp: check skb_pull_data() return in gtp1u_send_echo_resp()
gtp1u_send_echo_resp() ignores skb_pull_data()'s return value. Its
caller gtp1u_udp_encap_recv() only guarantees 16 bytes (udphdr +
gtp1_header), but the pull requests 20 (gtp1_header_long + udphdr). For
a 16-19 byte echo request the pull fails and returns NULL without
advancing skb->data; execution continues, and the following skb_push()
plus the IP header pushed by iptunnel_xmit() move skb->data below
skb->head, tripping skb_under_panic().
Fix it by dropping the packet when skb_pull_data() fails.
skbuff: skb_under_panic: ...
kernel BUG at net/core/skbuff.c:214!
Call Trace:
skb_push (net/core/skbuff.c:2648)
iptunnel_xmit (net/ipv4/ip_tunnel_core.c:82)
gtp_encap_recv (drivers/net/gtp.c:701 drivers/net/gtp.c:808 drivers/net/gtp.c:920)
udp_queue_rcv_one_skb (net/ipv4/udp.c:2388)
...
Kernel panic - not syncing: Fatal exception in interrupt |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: qca: fix NVM tag length underflow in TLV parser
In the TLV_TYPE_NVM branch of qca_tlv_check_data() the tag loop bound is
"while (idx < length - sizeof(struct tlv_type_nvm))". "length" is a signed
int from the firmware TLV header and sizeof(struct tlv_type_nvm) is a
size_t (12), so "length" is converted to size_t and any firmware-supplied
"length" < 12 makes the subtraction wrap to a huge value. The loop body
then reads a 12-byte struct tlv_type_nvm past the end of the short
vmalloc'd firmware buffer (and the EDL_TAG_ID_* handlers can write past it).
Rewrite the bound as "idx + sizeof(struct tlv_type_nvm) <= length"; both
operands are non-negative, so it no longer underflows and a "length" too
small for one record correctly skips the loop.
BUG: KASAN: vmalloc-out-of-bounds in qca_download_firmware.isra.0 (drivers/bluetooth/btqca.c:421)
Read of size 2 at addr ffffc900000e5004 by task kworker/u9:0/52
Workqueue: hci0 hci_power_on
Call Trace:
...
kasan_report (mm/kasan/report.c:595)
qca_download_firmware.isra.0 (drivers/bluetooth/btqca.c:421 drivers/bluetooth/btqca.c:617)
qca_uart_setup (drivers/bluetooth/btqca.c:948)
qca_setup (drivers/bluetooth/hci_qca.c:2029)
hci_uart_setup (drivers/bluetooth/hci_ldisc.c:438)
hci_dev_open_sync (net/bluetooth/hci_sync.c:5227)
hci_power_on (net/bluetooth/hci_core.c:920)
process_one_work (kernel/workqueue.c:3322)
worker_thread (kernel/workqueue.c:3486)
kthread (kernel/kthread.c:436)
ret_from_fork (arch/x86/kernel/process.c:158)
ret_from_fork_asm (arch/x86/entry/entry_64.S:245) |
| In the Linux kernel, the following vulnerability has been resolved:
Input: ims-pcu - fix heap-buffer-overflow in ims_pcu_process_data()
The `ims_pcu_process_data()` processes incoming URB data byte by byte.
However, it fails to check if the `read_pos` index exceeds
IMS_PCU_BUF_SIZE.
If a malicious USB device sends a packet larger than IMS_PCU_BUF_SIZE,
`read_pos` will increment indefinitely. Moreover, since `read_pos` is
located immediately after `read_buf`, the attacker can overwrite
`read_pos` itself to arbitrarily control the index.
This manipulated `read_pos` is subsequently used in
`ims_pcu_handle_response()` to copy data into `cmd_buf`, leading to a
heap buffer overflow.
Specifically, an attacker can overwrite the `cmd_done.wait.head` located
at offset 136 relative to `cmd_buf` in the `ims_pcu_handle_response()`.
Consequently, when the driver calls `complete(&pcu->cmd_done)`, it
triggers a control flow hijack by using the manipulated pointer.
Fix this by adding a bounds check for `read_pos` before writing to
`read_buf`. If the packet is too long, discard it, log a warning,
and reset the parser state.
[dtor: factor out resetting packet state, reset checksum as well] |
| In the Linux kernel, the following vulnerability has been resolved:
af_unix: Give up GC if MSG_PEEK intervened.
Igor Ushakov reported that GC purged the receive queue of
an alive socket due to a race with MSG_PEEK with a nice repro.
This is the exact same issue previously fixed by commit
cbcf01128d0a ("af_unix: fix garbage collect vs MSG_PEEK").
After GC was replaced with the current algorithm, the cited
commit removed the locking dance in unix_peek_fds() and
reintroduced the same issue.
The problem is that MSG_PEEK bumps a file refcount without
interacting with GC.
Consider an SCC containing sk-A and sk-B, where sk-A is
close()d but can be recv()ed via sk-B.
The bad thing happens if sk-A is recv()ed with MSG_PEEK from
sk-B and sk-B is close()d while GC is checking unix_vertex_dead()
for sk-A and sk-B.
GC thread User thread
--------- -----------
unix_vertex_dead(sk-A)
-> true <------.
\
`------ recv(sk-B, MSG_PEEK)
invalidate !! -> sk-A's file refcount : 1 -> 2
close(sk-B)
-> sk-B's file refcount : 2 -> 1
unix_vertex_dead(sk-B)
-> true
Initially, sk-A's file refcount is 1 by the inflight fd in sk-B
recvq. GC thinks sk-A is dead because the file refcount is the
same as the number of its inflight fds.
However, sk-A's file refcount is bumped silently by MSG_PEEK,
which invalidates the previous evaluation.
At this moment, sk-B's file refcount is 2; one by the open fd,
and one by the inflight fd in sk-A. The subsequent close()
releases one refcount by the former.
Finally, GC incorrectly concludes that both sk-A and sk-B are dead.
One option is to restore the locking dance in unix_peek_fds(),
but we can resolve this more elegantly thanks to the new algorithm.
The point is that the issue does not occur without the subsequent
close() and we actually do not need to synchronise MSG_PEEK with
the dead SCC detection.
When the issue occurs, close() and GC touch the same file refcount.
If GC sees the refcount being decremented by close(), it can just
give up garbage-collecting the SCC.
Therefore, we only need to signal the race during MSG_PEEK with
a proper memory barrier to make it visible to the GC.
Let's use seqcount_t to notify GC when MSG_PEEK occurs and let
it defer the SCC to the next run.
This way no locking is needed on the MSG_PEEK side, and we can
avoid imposing a penalty on every MSG_PEEK unnecessarily.
Note that we can retry within unix_scc_dead() if MSG_PEEK is
detected, but we do not do so to avoid hung task splat from
abusive MSG_PEEK calls. |
| In the Linux kernel, the following vulnerability has been resolved:
exfat: validate cluster allocation bits of the allocation bitmap
syzbot created an exfat image with cluster bits not set for the allocation
bitmap. exfat-fs reads and uses the allocation bitmap without checking
this. The problem is that if the start cluster of the allocation bitmap
is 6, cluster 6 can be allocated when creating a directory with mkdir.
exfat zeros out this cluster in exfat_mkdir, which can delete existing
entries. This can reallocate the allocated entries. In addition,
the allocation bitmap is also zeroed out, so cluster 6 can be reallocated.
This patch adds exfat_test_bitmap_range to validate that clusters used for
the allocation bitmap are correctly marked as in-use. |
