| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: contpte: fix set_access_flags() no-op check for SMMU/ATS faults
contpte_ptep_set_access_flags() compared the gathered ptep_get() value
against the requested entry to detect no-ops. ptep_get() ORs AF/dirty
from all sub-PTEs in the CONT block, so a dirty sibling can make the
target appear already-dirty. When the gathered value matches entry, the
function returns 0 even though the target sub-PTE still has PTE_RDONLY
set in hardware.
For a CPU with FEAT_HAFDBS this gathered view is fine, since hardware may
set AF/dirty on any sub-PTE and CPU TLB behavior is effectively gathered
across the CONT range. But page-table walkers that evaluate each
descriptor individually (e.g. a CPU without DBM support, or an SMMU
without HTTU, or with HA/HD disabled in CD.TCR) can keep faulting on the
unchanged target sub-PTE, causing an infinite fault loop.
Gathering can therefore cause false no-ops when only a sibling has been
updated:
- write faults: target still has PTE_RDONLY (needs PTE_RDONLY cleared)
- read faults: target still lacks PTE_AF
Fix by checking each sub-PTE against the requested AF/dirty/write state
(the same bits consumed by __ptep_set_access_flags()), using raw
per-PTE values rather than the gathered ptep_get() view, before
returning no-op. Keep using the raw target PTE for the write-bit unfold
decision.
Per Arm ARM (DDI 0487) D8.7.1 ("The Contiguous bit"), any sub-PTE in a CONT
range may become the effective cached translation and software must
maintain consistent attributes across the range. |
| In the Linux kernel, the following vulnerability has been resolved:
liveupdate: luo_file: remember retrieve() status
LUO keeps track of successful retrieve attempts on a LUO file. It does so
to avoid multiple retrievals of the same file. Multiple retrievals cause
problems because once the file is retrieved, the serialized data
structures are likely freed and the file is likely in a very different
state from what the code expects.
The retrieve boolean in struct luo_file keeps track of this, and is passed
to the finish callback so it knows what work was already done and what it
has left to do.
All this works well when retrieve succeeds. When it fails,
luo_retrieve_file() returns the error immediately, without ever storing
anywhere that a retrieve was attempted or what its error code was. This
results in an errored LIVEUPDATE_SESSION_RETRIEVE_FD ioctl to userspace,
but nothing prevents it from trying this again.
The retry is problematic for much of the same reasons listed above. The
file is likely in a very different state than what the retrieve logic
normally expects, and it might even have freed some serialization data
structures. Attempting to access them or free them again is going to
break things.
For example, if memfd managed to restore 8 of its 10 folios, but fails on
the 9th, a subsequent retrieve attempt will try to call
kho_restore_folio() on the first folio again, and that will fail with a
warning since it is an invalid operation.
Apart from the retry, finish() also breaks. Since on failure the
retrieved bool in luo_file is never touched, the finish() call on session
close will tell the file handler that retrieve was never attempted, and it
will try to access or free the data structures that might not exist, much
in the same way as the retry attempt.
There is no sane way of attempting the retrieve again. Remember the error
retrieve returned and directly return it on a retry. Also pass this
status code to finish() so it can make the right decision on the work it
needs to do.
This is done by changing the bool to an integer. A value of 0 means
retrieve was never attempted, a positive value means it succeeded, and a
negative value means it failed and the error code is the value. |
| In the Linux kernel, the following vulnerability has been resolved:
mfd: macsmc: Initialize mutex
Initialize struct apple_smc's mutex in apple_smc_probe(). Using the
mutex uninitialized surprisingly resulted only in occasional NULL
pointer dereferences in apple_smc_read() calls from the probe()
functions of sub devices. |
| In the Linux kernel, the following vulnerability has been resolved:
Revert "media: iris: Add sanity check for stop streaming"
This reverts commit ad699fa78b59241c9d71a8cafb51525f3dab04d4.
Revert the check that skipped stop_streaming when the instance was in
IRIS_INST_ERROR, as it caused multiple regressions:
1. Buffers were not returned to vb2 when the instance was already in
error state, triggering warnings in the vb2 core because buffer
completion was skipped.
2. If a session failed early (e.g. unsupported configuration), the
instance transitioned to IRIS_INST_ERROR. When userspace attempted
to stop streaming for cleanup, stop_streaming was skipped due to the
added check, preventing proper teardown and leaving the firmware
in an inconsistent state. |
| In the Linux kernel, the following vulnerability has been resolved:
ntb: ntb_hw_switchtec: Fix shift-out-of-bounds for 0 mw lut
Number of MW LUTs depends on NTB configuration and can be set to zero,
in such scenario rounddown_pow_of_two will cause undefined behaviour and
should not be performed.
This patch ensures that rounddown_pow_of_two is called on valid value. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: ti_fpc202: fix a potential memory leak in probe function
Use for_each_child_of_node_scoped() to simplify the code and ensure the
device node reference is automatically released when the loop scope
ends. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (nct7363) Fix a resource leak in nct7363_present_pwm_fanin
When calling of_parse_phandle_with_args(), the caller is responsible
to call of_node_put() to release the reference of device node.
In nct7363_present_pwm_fanin, it does not release the reference,
causing a resource leak. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix null dereference in find_network
The variable pwlan has the possibility of being NULL when passed into
rtw_free_network_nolock() which would later dereference the variable. |
| In the Linux kernel, the following vulnerability has been resolved:
media: tegra-video: Fix memory leak in __tegra_channel_try_format()
The state object allocated by __v4l2_subdev_state_alloc() must be freed
with __v4l2_subdev_state_free() when it is no longer needed.
In __tegra_channel_try_format(), two error paths return directly after
v4l2_subdev_call() fails, without freeing the allocated 'sd_state'
object. This violates the requirement and causes a memory leak.
Fix this by introducing a cleanup label and using goto statements in the
error paths to ensure that __v4l2_subdev_state_free() is always called
before the function returns. |
| In the Linux kernel, the following vulnerability has been resolved:
udplite: Fix null-ptr-deref in __udp_enqueue_schedule_skb().
syzbot reported null-ptr-deref of udp_sk(sk)->udp_prod_queue. [0]
Since the cited commit, udp_lib_init_sock() can fail, as can
udp_init_sock() and udpv6_init_sock().
Let's handle the error in udplite_sk_init() and udplitev6_sk_init().
[0]:
BUG: KASAN: null-ptr-deref in instrument_atomic_read include/linux/instrumented.h:82 [inline]
BUG: KASAN: null-ptr-deref in atomic_read include/linux/atomic/atomic-instrumented.h:32 [inline]
BUG: KASAN: null-ptr-deref in __udp_enqueue_schedule_skb+0x151/0x1480 net/ipv4/udp.c:1719
Read of size 4 at addr 0000000000000008 by task syz.2.18/2944
CPU: 1 UID: 0 PID: 2944 Comm: syz.2.18 Not tainted syzkaller #0 PREEMPTLAZY
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/25/2025
Call Trace:
<IRQ>
dump_stack_lvl+0xe8/0x150 lib/dump_stack.c:120
kasan_report+0xa2/0xe0 mm/kasan/report.c:595
check_region_inline mm/kasan/generic.c:-1 [inline]
kasan_check_range+0x264/0x2c0 mm/kasan/generic.c:200
instrument_atomic_read include/linux/instrumented.h:82 [inline]
atomic_read include/linux/atomic/atomic-instrumented.h:32 [inline]
__udp_enqueue_schedule_skb+0x151/0x1480 net/ipv4/udp.c:1719
__udpv6_queue_rcv_skb net/ipv6/udp.c:795 [inline]
udpv6_queue_rcv_one_skb+0xa2e/0x1ad0 net/ipv6/udp.c:906
udp6_unicast_rcv_skb+0x227/0x380 net/ipv6/udp.c:1064
ip6_protocol_deliver_rcu+0xe17/0x1540 net/ipv6/ip6_input.c:438
ip6_input_finish+0x191/0x350 net/ipv6/ip6_input.c:489
NF_HOOK+0x354/0x3f0 include/linux/netfilter.h:318
ip6_input+0x16c/0x2b0 net/ipv6/ip6_input.c:500
NF_HOOK+0x354/0x3f0 include/linux/netfilter.h:318
__netif_receive_skb_one_core net/core/dev.c:6149 [inline]
__netif_receive_skb+0xd3/0x370 net/core/dev.c:6262
process_backlog+0x4d6/0x1160 net/core/dev.c:6614
__napi_poll+0xae/0x320 net/core/dev.c:7678
napi_poll net/core/dev.c:7741 [inline]
net_rx_action+0x60d/0xdc0 net/core/dev.c:7893
handle_softirqs+0x209/0x8d0 kernel/softirq.c:622
do_softirq+0x52/0x90 kernel/softirq.c:523
</IRQ>
<TASK>
__local_bh_enable_ip+0xe7/0x120 kernel/softirq.c:450
local_bh_enable include/linux/bottom_half.h:33 [inline]
rcu_read_unlock_bh include/linux/rcupdate.h:924 [inline]
__dev_queue_xmit+0x109c/0x2dc0 net/core/dev.c:4856
__ip6_finish_output net/ipv6/ip6_output.c:-1 [inline]
ip6_finish_output+0x158/0x4e0 net/ipv6/ip6_output.c:219
NF_HOOK_COND include/linux/netfilter.h:307 [inline]
ip6_output+0x342/0x580 net/ipv6/ip6_output.c:246
ip6_send_skb+0x1d7/0x3c0 net/ipv6/ip6_output.c:1984
udp_v6_send_skb+0x9a5/0x1770 net/ipv6/udp.c:1442
udp_v6_push_pending_frames+0xa2/0x140 net/ipv6/udp.c:1469
udpv6_sendmsg+0xfe0/0x2830 net/ipv6/udp.c:1759
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg+0xe5/0x270 net/socket.c:742
__sys_sendto+0x3eb/0x580 net/socket.c:2206
__do_sys_sendto net/socket.c:2213 [inline]
__se_sys_sendto net/socket.c:2209 [inline]
__x64_sys_sendto+0xde/0x100 net/socket.c:2209
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xd2/0xf20 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f67b4d9c629
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f67b5c98028 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007f67b5015fa0 RCX: 00007f67b4d9c629
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003
RBP: 00007f67b4e32b39 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000040000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007f67b5016038 R14: 00007f67b5015fa0 R15: 00007ffe3cb66dd8
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix interlaced plain identification for encoded extents
Only plain data whose start position and on-disk physical length are
both aligned to the block size should be classified as interlaced
plain extents. Otherwise, it must be treated as shifted plain extents.
This issue was found by syzbot using a crafted compressed image
containing plain extents with unaligned physical lengths, which can
cause OOB read in z_erofs_transform_plain(). |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: Fix potential kernel oops when probe fails
When probe of the sdio brcmfmac device fails for some reasons (i.e.
missing firmware), the sdiodev->bus is set to error instead of NULL, thus
the cleanup later in brcmf_sdio_remove() tries to free resources via
invalid bus pointer. This happens because sdiodev->bus is set 2 times:
first in brcmf_sdio_probe() and second time in brcmf_sdiod_probe(). Fix
this by chaning the brcmf_sdio_probe() function to return the error code
and set sdio->bus only there. |
| In the Linux kernel, the following vulnerability has been resolved:
remoteproc: imx_rproc: Fix invalid loaded resource table detection
imx_rproc_elf_find_loaded_rsc_table() may incorrectly report a loaded
resource table even when the current firmware does not provide one.
When the device tree contains a "rsc-table" entry, priv->rsc_table is
non-NULL and denotes where a resource table would be located if one is
present in memory. However, when the current firmware has no resource
table, rproc->table_ptr is NULL. The function still returns
priv->rsc_table, and the remoteproc core interprets this as a valid loaded
resource table.
Fix this by returning NULL from imx_rproc_elf_find_loaded_rsc_table() when
there is no resource table for the current firmware (i.e. when
rproc->table_ptr is NULL). This aligns the function's semantics with the
remoteproc core: a loaded resource table is only reported when a valid
table_ptr exists.
With this change, starting firmware without a resource table no longer
triggers a crash. |
| In the Linux kernel, the following vulnerability has been resolved:
mux: mmio: fix regmap leak on probe failure
The mmio regmap that may be allocated during probe is never freed.
Switch to using the device managed allocator so that the regmap is
released on probe failures (e.g. probe deferral) and on driver unbind. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: bcm_vk: Fix possible null-pointer dereferences in bcm_vk_read()
In the function bcm_vk_read(), the pointer entry is checked, indicating
that it can be NULL. If entry is NULL and rc is set to -EMSGSIZE, the
following code may cause null-pointer dereferences:
struct vk_msg_blk tmp_msg = entry->to_h_msg[0];
set_msg_id(&tmp_msg, entry->usr_msg_id);
tmp_msg.size = entry->to_h_blks - 1;
To prevent these possible null-pointer dereferences, copy to_h_msg,
usr_msg_id, and to_h_blks from iter into temporary variables, and return
these temporary variables to the application instead of accessing them
through a potentially NULL entry. |
| In the Linux kernel, the following vulnerability has been resolved:
media: iris: Add buffer to list only after successful allocation
Move `list_add_tail()` to after `dma_alloc_attrs()` succeeds when creating
internal buffers. Previously, the buffer was enqueued in `buffers->list`
before the DMA allocation. If the allocation failed, the function returned
`-ENOMEM` while leaving a partially initialized buffer in the list, which
could lead to inconsistent state and potential leaks.
By adding the buffer to the list only after `dma_alloc_attrs()` succeeds,
we ensure the list contains only valid, fully initialized buffers. |
| In the Linux kernel, the following vulnerability has been resolved:
net: wan/fsl_ucc_hdlc: Fix dma_free_coherent() in uhdlc_memclean()
The priv->rx_buffer and priv->tx_buffer are alloc'd together as
contiguous buffers in uhdlc_init() but freed as two buffers in
uhdlc_memclean().
Change the cleanup to only call dma_free_coherent() once on the whole
buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix incorrect early exits in volume label handling
Crafted EROFS images containing valid volume labels can trigger
incorrect early returns, leading to folio reference leaks.
However, this does not cause system crashes or other severe issues. |
| In the Linux kernel, the following vulnerability has been resolved:
memory: mtk-smi: fix device leak on larb probe
Make sure to drop the reference taken when looking up the SMI device
during larb probe on late probe failure (e.g. probe deferral) and on
driver unbind. |
| In the Linux kernel, the following vulnerability has been resolved:
memory: mtk-smi: fix device leaks on common probe
Make sure to drop the reference taken when looking up the SMI device
during common probe on late probe failure (e.g. probe deferral) and on
driver unbind. |
