| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ieee802154: ca8210: fix pointer truncation in kfifo on 64-bit
ca8210_test_int_driver_write() and ca8210_test_int_user_read() exchange
a kmalloc'd buffer pointer through a struct kfifo, but pass a literal
'4' as the byte count to kfifo_in()/kfifo_out().
This is correct on 32-bit (pointer = 4 bytes), but on 64-bit only the
low 4 bytes of the 8-byte pointer are written into the FIFO. The reader
then reads back 4 bytes into an 8-byte local pointer variable, leaving
the upper 4 bytes uninitialized stack data. The first dereference of
the reconstructed pointer (fifo_buffer[1]) accesses an arbitrary kernel
address and generally results in an oops.
Use sizeof(fifo_buffer) so the byte count matches pointer width on every
architecture.
The driver has no architecture restriction in Kconfig, so any 64-bit
build with CONFIG_IEEE802154_CA8210_DEBUGFS=y is exposed. Issue has
been latent since the driver was added in 2017 because it is most
commonly deployed on 32-bit MCUs.
Found via a custom Coccinelle semantic patch hunting for short-byte
kfifo I/O on byte-mode kfifos used to shuttle pointers. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: probes: save original sp in rethook trampoline
Reading a word from the stack in a kretprobe crashes a risc-v kernel.
$ cd /sys/kernel/tracing/
$ echo 'r n_tty_write $stack0' > dynamic_events
$ echo 1 > events/kprobes/enable
Unable to handle kernel paging request at virtual address 0000000200000128
...
[<ffffffff80016d16>] regs_get_kernel_stack_nth+0x26/0x38
[<ffffffff80177196>] process_fetch_insn+0x3ee/0x760
[<ffffffff80177836>] kretprobe_trace_func+0x116/0x1f0
[<ffffffff8017795a>] kretprobe_dispatcher+0x4a/0x58
[<ffffffff8013572e>] kretprobe_rethook_handler+0x5e/0x90
[<ffffffff80180838>] rethook_trampoline_handler+0x70/0x108
[<ffffffff8001ba32>] arch_rethook_trampoline_callback+0x12/0x1c
[<ffffffff8001ba84>] arch_rethook_trampoline+0x48/0x94
[<ffffffff8067872a>] tty_write+0x1a/0x30
In regs_get_kernel_stack_nth, regs->sp contains an arbitrary value.
arch_rethook_trampoline saves the registers from the probed function in a
struct pt_regs. sp is not saved. Instead, sp is decremented for
arch_rethook_trampoline's local stack.
Fix this crash and save the original sp along with the other registers.
Use a0 as a temporary register, it is overwritten anyway.
[pjw@kernel.org: added Fixes tag; cc'ed stable] |
| The user-space system-call verifier z_vrfy_z_log_msg_static_create() in subsys/logging/log_msg.c was a pure pass-through: it forwarded the caller-supplied source, desc, package, and data arguments directly to the kernel-mode implementation z_impl_z_log_msg_static_create() without performing any of the mandatory K_SYSCALL_* checks. Because z_log_msg_static_create() is declared __syscall, under CONFIG_USERSPACE any unprivileged user-mode thread can invoke it directly with fully attacker-controlled arguments.
The kernel-mode handler dereferences each of these untrusted values: frontend_runtime_filtering() reads through the source pointer as a struct log_source_dynamic_data, cbprintf_package_copy() reads desc.package_len bytes from the package pointer, and z_log_msg_finalize() performs a memcpy() of desc.data_len bytes from the data pointer. With no verification, a user thread can supply arbitrary kernel addresses and arbitrary lengths, and the kernel will read from them.
The impact is a kernel-mode denial of service (the kernel faults dereferencing an attacker-chosen pointer) and, where a log backend output is observable to the attacker, disclosure of arbitrary kernel memory copied into the emitted log message — a confidentiality breach across the user/kernel boundary that the userspace sandbox is meant to enforce. The reads do not corrupt kernel memory, so there is no out-of-bounds write primitive.
The fix adds the required validation to the verifier: it bounds desc.package_len against Z_LOG_MSG_MAX_PACKAGE, rejects non-NULL/length mismatches, and applies K_SYSCALL_MEMORY_READ() to package, data, and (when runtime filtering with a frontend is enabled) source, so any out-of-bounds or kernel pointer now raises K_OOPS instead of being honored. |
| LightFTP through 2.4 contains multiple data race vulnerabilities in ftpserv.c that allow anonymous attackers to cause undefined behavior by issuing LIST followed by ABOR commands without authentication. The control thread closes data_socket and file_fd descriptors while worker threads concurrently operate on the same fields in worker_thread_cleanup, allowing stale file descriptors to be reassigned by the OS and subsequently used by worker threads on unrelated resources, resulting in potential denial of service. |
| FFmpeg versions from 0.5 up to, but not including, 9.0 contain an uninitialized heap memory disclosure vulnerability in the native TIFF decoder in libavcodec/tiff.c. An attacker who can cause FFmpeg to decode a crafted TIFF file can supply a valid Deflate-compressed strip that terminates successfully after producing fewer bytes than the declared strip requires. The tiff_unpack_zlib() function allocates a heap buffer sized for the full declared strip but copies all declared rows via memcpy() regardless of how many bytes zlib actually decompressed, causing unwritten bytes that can contain stale data from prior heap allocations to be incorporated into decoded image output and potentially exposing sensitive data in persistent services. |
| FFmpeg versions from 3.0 up to, but not including, 9.0 contain an uninitialized heap memory read vulnerability in the native Screenpresso decoder (libavcodec/screenpresso.c) that allows attackers to recover sensitive memory contents by supplying a crafted SPV1 packet with a valid zlib stream that decompresses fewer bytes than the full frame requires. The screenpresso_decode_frame() function fails to validate the produced byte count before calling av_image_copy_plane() to copy the complete frame dimensions from the persistent ctx->inflated_buf buffer, causing unwritten heap memory from prior allocations or prior frames to be copied into decoded output and potentially exposing sensitive data such as userspace addresses from persistent decoding services. |
| llama.cpp builds b7492 through the latest b9060 contains a use-after-free vulnerability in the vocab pointer of llama-server when the --sleep-idle-seconds feature is enabled, allowing unauthenticated remote attackers to execute arbitrary code. Attackers can trigger the vulnerability by sending requests to affected endpoints while the server transitions to sleep mode, causing concurrent worker threads to dereference a freed vocab pointer that can be reclaimed with attacker-controlled data to achieve remote code execution. |
| In the Linux kernel, the following vulnerability has been resolved:
inet: frags: fix use-after-free caused by the fqdir_pre_exit() flush
On netns teardown, fqdir_pre_exit() walks the fqdir rhashtable and
flushes every fragment queue that is not yet complete using
inet_frag_queue_flush(). That helper frees all the skbs queued on the
fragment queue but does not set INET_FRAG_COMPLETE, and leaves
q->fragments_tail and q->last_run_head pointing at the freed skbs.
The queue itself stays in the rhashtable.
fqdir_pre_exit() first lowers high_thresh to 0 to stop new queue lookups,
but it cannot stop a fragment that already obtained the queue through
inet_frag_find() earlier and stalled just before taking the queue lock.
Once that fragment resumes after the flush and takes the queue lock,
it passes the INET_FRAG_COMPLETE check and then dereferences the freed
fragments_tail. inet_frag_queue_insert() reads FRAG_CB() and ->len of
that pointer and, on the append path, writes ->next_frag, causing a
slab use-after-free. IPv6, nf_conntrack_reasm6 and 6lowpan reassembly
share the same flush path and are affected as well.
Reset rb_fragments, fragments_tail and last_run_head in
inet_frag_queue_flush() so a flushed queue no longer points at the
freed skbs. A fragment that resumes after the flush and takes the
queue lock then finds an empty queue and starts a new run instead of
dereferencing the freed fragments_tail. ip_frag_reinit() already
performed this reset after its own flush, so drop the now duplicate
code there. |
| Untrusted pointer dereference in Windows GDI allows an authorized attacker to disclose information locally. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: clear mode callbacks after failed mode setup
xfrm_state_gc_task can run long after a failed IPTFS state setup. In the
reproduced case, __xfrm_init_state() cached x->mode_cbs, IPTFS setup
returned -ENOMEM before publishing mode_data, and the temporary module
reference from xfrm_get_mode_cbs() was dropped immediately. The dead state
then kept x->mode_cbs until deferred GC ran after xfrm_iptfs had been
unloaded.
Clear x->mode_cbs when mode init or clone fails before publishing
mode_data. Those states never installed mode-specific state or the
long-term IPTFS module pin, so deferred GC has nothing mode-specific to
destroy and must not retain a callback table pointer past the temporary
lookup reference.
The buggy scenario involves two paths, with each column showing the order
within that path:
failed setup path:
1. cache x->mode_cbs
2. mode setup fails before mode_data
3. drop the temporary module ref
4. dead state keeps x->mode_cbs cached
GC/unload path:
1. xfrm_state_put() queues GC work
2. xfrm_iptfs unloads later
3. xfrm_state_gc_task runs
4. GC dereferences stale x->mode_cbs
This also covers the failed clone path where clone_state() returns before
publishing mode_data.
Validation reproduced this kernel report:
Kernel panic - not syncing: Fatal exception
CONFIG_FAULT_INJECTION_STACKTRACE_FILTER=y
failslab_stacktrace_filter matched xfrm_iptfs frames
ack_error=-12
FAULT_INJECTION: forcing a failure
BUG: unable to handle page fault
Workqueue: events xfrm_state_gc_task
RIP: xfrm_state_gc_task+0x142/0x650
Modules linked in: esp4_offload xfrm_user [last unloaded: xfrm_iptfs]
Kernel panic - not syncing: Fatal exception |
| In the Linux kernel, the following vulnerability has been resolved:
media: rc: igorplugusb: heed coherency rules
In a control request, the USB request structure
can be subject to DMA on some HCs. Hence it must obey
the rules for DMA coherency. Allocate it separately. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_qca: Clear memdump state on invalid dump size
qca_controller_memdump() allocates qca->qca_memdump before processing
the first dump packet. For a sequence-zero packet it then disables IBS,
marks memdump collection active, and reads the advertised dump size.
If the controller reports a zero dump size, the error path frees the
local qca_memdump object and returns without clearing qca->qca_memdump
or undoing the collection state. A later memdump work item initializes
its local pointer from qca->qca_memdump and skips allocation when that
pointer is non-NULL, so it can operate on freed memory. The stale
collection and IBS-disabled flags can also leave waiters or later
transmit handling blocked behind an aborted dump.
Clear the saved pointer and memdump state before returning from the
invalid-size path, matching the cleanup used when hci_devcd_init() fails.
A static analysis checker reported the stale memdump state, and manual
source review confirmed the invalid-size failure path. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/amdxdna: Fix use-after-free of mm_struct in job scheduler
amdxdna_cmd_submit() stores current->mm in job->mm without holding any
reference. aie2_sched_job_run() later access job->mm from the DRM
scheduler worker thread. With only a raw pointer and no structural
reference, the mm_struct can be freed before the scheduler runs the job.
Fix this by calling mmgrab() to hold a structural mm_count reference for
the lifetime of the job, paired with mmdrop() in every cleanup path. |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: fix use after free in unlock_ovpn()
unlock_ovpn() iterates over the release_list using llist_for_each_entry()
and drops the peer reference inside the loop body via ovpn_peer_put().
If this drops the last reference, the peer is eventually freed. However,
llist_for_each_entry() reads peer->release_entry.next in the loop advance
expression, which runs after the body. By that time the peer may have
already been freed, resulting in a use after free when advancing to the
next list entry.
Fix this by using llist_for_each_entry_safe(), which caches the next
pointer before executing the loop body. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Fix use-after-free freeing trigger private data
Commit 61d445af0a7c ("tracing: Add bulk garbage collection of freeing
event_trigger_data") moved the kfree() of event_trigger_data to a kthread
that runs tracepoint_synchronize_unregister() before freeing. That removed
the synchronization the trigger .free callbacks used to get implicitly and
inline from trigger_data_free().
event_hist_trigger_free(), event_hist_trigger_named_free() and
event_enable_trigger_free() free their satellite data (hist_data, cmd_ops,
enable_data) right after trigger_data_free() returns. With the
synchronization now deferred to the kthread, a concurrent tracepoint
handler can still reach that data through the list_del_rcu()'d trigger,
causing a use-after-free.
The histogram teardown must stay synchronous: remove_hist_vars() and
unregister_field_var_hists() have to detach a synthetic event from the
histogram before the trigger-removal write returns, otherwise a following
command races in and the synthetic-event removal fails with -EBUSY, as the
trigger-synthetic-eprobe.tc selftest catches. Make those callbacks wait
with the correct barrier - tracepoint_synchronize_unregister(), matching
the free kthread - before freeing.
The enable trigger has no such synchronous requirement, and a blocking
synchronize there would re-serialize the path that commit deliberately
deferred. Give it an optional private_data_free() callback that the free
kthread runs after its grace period, and free enable_data from there. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Delay module ref count for "enable_event" trigger
Triggers are now delayed from freeing, but can still be triggered until
after the RCU grace period has ended. The freeing of the enable_event data
is put into the private_data_free() callback, but the put of the module
refcount is done immediately.
It is possible that if a module is removed that has an event that would
enable (or disable) it is still active, it can read the data of the module
after it is removed causing a use-after-free bug.
Move the trace_event_put_ref() that releases the module into the delayed
callback so that the module can not be removed until any reference to its
events are finished. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: make huge_ptep_get handled unaligned addresses
huge_ptep_get() can be handed a virtual address pointing to the middle
of a contpmd/contpte mapped hugetlb folio (examples of callers are
pagemap_hugetlb_range, page_mapped_in_vma).
The arm64 helper rewalks the pgtables in find_num_contig to answer
whether the huge pte we have maps a contpmd or a contpte hugetlb folio,
and returns CONT_PMDS or CONT_PTES, so that it can collect a/d bits over
the contiguous ptes. We can falsely return CONT_PTES instead of
CONT_PMDS if the addr is not aligned. On systems where CONT_PTES !=
CONT_PMDS (meaning page size is 16K), we could collect excess A/D bit
state, meaning extra work for the kernel. Even worse, we may iterate
beyond the PTE table and dereference a garbage ptep pointer to access
physical memory we don't own. Since the ptep pointer is a linear map
address, we may run off the end of the linear map or into a hole,
dereference a VA not mapped into the kernel pgtables and cause kernel
panic.
Fix this by aligning the pmdp pointer down to a contpmd base before
checking equality with the passed huge pte pointer, to correctly answer
whether the huge pte is the base of a contpmd block. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: fix stale skb->sk reference on subflow close
The backlog list is updated by mptcp_data_ready() under
mptcp_data_lock(). The cleanup of backlog references to a closing
subflow, however, was performed in mptcp_close_ssk(), before
__mptcp_close_ssk() acquires the ssk lock, and while holding neither
the ssk lock nor mptcp_data_lock().
Because that traversal ran without mptcp_data_lock(), concurrent softirq
RX processing on another CPU (subflow_data_ready() -> mptcp_data_ready()
-> __mptcp_add_backlog(), under mptcp_data_lock()) could add a backlog
entry referencing the ssk while the cleanup loop was in progress. Such
an entry could be missed by the cleanup, or the concurrent list update
could corrupt the traversal, leaving skb->sk pointing at the ssk after
it is freed.
A later mptcp_backlog_purge() then dereferences the stale pointer,
triggering a warning in inet_sock_destruct() (ssk->sk_rmem_alloc != 0)
followed by a use-after-free in mptcp_backlog_purge().
Fix this by moving the backlog cleanup into __mptcp_close_ssk(), after
subflow->closing is set to 1 and while the ssk lock is still held,
serialized under mptcp_data_lock(). The cleanup runs only on the push
path (MPTCP_CF_PUSH), where backlog references accumulate; on other
teardown paths the caller already handles cleanup.
With subflow->closing set and mptcp_data_lock() held across the purge,
any concurrent mptcp_data_ready() either completes its enqueue before
the purge runs and is caught, or observes closing=1 and bails out. Once
mptcp_data_unlock() is reached, no new skb referencing the ssk can be
enqueued, so the cleanup is exhaustive.
Remove the unprotected traversal from mptcp_close_ssk() entirely. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx-lpi2c: mark I2C adapter when hardware is powered down
On some i.MX platforms, certain I2C client drivers keep a periodic
workqueue which continues to trigger I2C transfers.
During system suspend/resume, there exists a time window between:
- suspend_noirq and the system entering suspend
- the system starting to resume and resume_noirq
In this window, the I2C controller resources such as clock and pinctrl
may already be disabled or not yet restored.
If a workqueue triggers an I2C transfer in this period, the driver
attempts to access I2C registers while the hardware resources are
unavailable, which may lead to system hang.
Mark the I2C adapter as suspended during noirq suspend and block new
transfers until resume, ensuring that I2C transfers are only issued
when hardware resources are available. |
| Untrusted pointer dereference in Microsoft Office Excel allows an unauthorized attacker to execute code locally. |
