| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix sleeping-in-atomic in ath11k_mac_op_set_bitrate_mask()
ath11k_mac_disable_peer_fixed_rate() is passed as the iterator to
ieee80211_iterate_stations_atomic(). Note in this case the iterator is
required to be atomic, however ath11k_mac_disable_peer_fixed_rate() does
not follow it as it might sleep. Consequently below warning is seen:
BUG: sleeping function called from invalid context at wmi.c:304
Call Trace:
<TASK>
dump_stack_lvl
__might_resched.cold
ath11k_wmi_cmd_send
ath11k_wmi_set_peer_param
ath11k_mac_disable_peer_fixed_rate
ieee80211_iterate_stations_atomic
ath11k_mac_op_set_bitrate_mask.cold
Change to ieee80211_iterate_stations_mtx() to fix this issue.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30 |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: Fix backlog accounting in qdisc_dequeue_internal
This issue applies for the following qdiscs: hhf, fq, fq_codel, and
fq_pie, and occurs in their change handlers when adjusting to the new
limit. The problem is the following in the values passed to the
subsequent qdisc_tree_reduce_backlog call given a tbf parent:
When the tbf parent runs out of tokens, skbs of these qdiscs will
be placed in gso_skb. Their peek handlers are qdisc_peek_dequeued,
which accounts for both qlen and backlog. However, in the case of
qdisc_dequeue_internal, ONLY qlen is accounted for when pulling
from gso_skb. This means that these qdiscs are missing a
qdisc_qstats_backlog_dec when dropping packets to satisfy the
new limit in their change handlers.
One can observe this issue with the following (with tc patched to
support a limit of 0):
export TARGET=fq
tc qdisc del dev lo root
tc qdisc add dev lo root handle 1: tbf rate 8bit burst 100b latency 1ms
tc qdisc replace dev lo handle 3: parent 1:1 $TARGET limit 1000
echo ''; echo 'add child'; tc -s -d qdisc show dev lo
ping -I lo -f -c2 -s32 -W0.001 127.0.0.1 2>&1 >/dev/null
echo ''; echo 'after ping'; tc -s -d qdisc show dev lo
tc qdisc change dev lo handle 3: parent 1:1 $TARGET limit 0
echo ''; echo 'after limit drop'; tc -s -d qdisc show dev lo
tc qdisc replace dev lo handle 2: parent 1:1 sfq
echo ''; echo 'post graft'; tc -s -d qdisc show dev lo
The second to last show command shows 0 packets but a positive
number (74) of backlog bytes. The problem becomes clearer in the
last show command, where qdisc_purge_queue triggers
qdisc_tree_reduce_backlog with the positive backlog and causes an
underflow in the tbf parent's backlog (4096 Mb instead of 0).
To fix this issue, the codepath for all clients of qdisc_dequeue_internal
has been simplified: codel, pie, hhf, fq, fq_pie, and fq_codel.
qdisc_dequeue_internal handles the backlog adjustments for all cases that
do not directly use the dequeue handler.
The old fq_codel_change limit adjustment loop accumulated the arguments to
the subsequent qdisc_tree_reduce_backlog call through the cstats field.
However, this is confusing and error prone as fq_codel_dequeue could also
potentially mutate this field (which qdisc_dequeue_internal calls in the
non gso_skb case), so we have unified the code here with other qdiscs. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: nintendo: avoid bluetooth suspend/resume stalls
Ensure we don't stall or panic the kernel when using bluetooth-connected
controllers. This was reported as an issue on android devices using
kernel 6.6 due to the resume hook which had been added for usb joycons.
First, set a new state value to JOYCON_CTLR_STATE_SUSPENDED in a
newly-added nintendo_hid_suspend. This makes sure we will not stall out
the kernel waiting for input reports during led classdev suspend. The
stalls could happen if connectivity is unreliable or lost to the
controller prior to suspend.
Second, since we lose connectivity during suspend, do not try
joycon_init() for bluetooth controllers in the nintendo_hid_resume path.
Tested via multiple suspend/resume flows when using the controller both
in USB and bluetooth modes. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850
GCC_GCC_PCIE_HOT_RST is wrongly defined for WCN7850, causing kernel crash
on some specific platforms.
Since this register is divergent for WCN7850 and QCN9274, move it to
register table to allow different definitions. Then correct the register
address for WCN7850 to fix this issue.
Note IPQ5332 is not affected as it is not PCIe based device.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Do not include stack ptr register in precision backtracking bookkeeping
Yi Lai reported an issue ([1]) where the following warning appears
in kernel dmesg:
[ 60.643604] verifier backtracking bug
[ 60.643635] WARNING: CPU: 10 PID: 2315 at kernel/bpf/verifier.c:4302 __mark_chain_precision+0x3a6c/0x3e10
[ 60.648428] Modules linked in: bpf_testmod(OE)
[ 60.650471] CPU: 10 UID: 0 PID: 2315 Comm: test_progs Tainted: G OE 6.15.0-rc4-gef11287f8289-dirty #327 PREEMPT(full)
[ 60.654385] Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
[ 60.656682] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.14.0-0-g155821a1990b-prebuilt.qemu.org 04/01/2014
[ 60.660475] RIP: 0010:__mark_chain_precision+0x3a6c/0x3e10
[ 60.662814] Code: 5a 30 84 89 ea e8 c4 d9 01 00 80 3d 3e 7d d8 04 00 0f 85 60 fa ff ff c6 05 31 7d d8 04
01 48 c7 c7 00 58 30 84 e8 c4 06 a5 ff <0f> 0b e9 46 fa ff ff 48 ...
[ 60.668720] RSP: 0018:ffff888116cc7298 EFLAGS: 00010246
[ 60.671075] RAX: 54d70e82dfd31900 RBX: ffff888115b65e20 RCX: 0000000000000000
[ 60.673659] RDX: 0000000000000001 RSI: 0000000000000004 RDI: 00000000ffffffff
[ 60.676241] RBP: 0000000000000400 R08: ffff8881f6f23bd3 R09: 1ffff1103ede477a
[ 60.678787] R10: dffffc0000000000 R11: ffffed103ede477b R12: ffff888115b60ae8
[ 60.681420] R13: 1ffff11022b6cbc4 R14: 00000000fffffff2 R15: 0000000000000001
[ 60.684030] FS: 00007fc2aedd80c0(0000) GS:ffff88826fa8a000(0000) knlGS:0000000000000000
[ 60.686837] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 60.689027] CR2: 000056325369e000 CR3: 000000011088b002 CR4: 0000000000370ef0
[ 60.691623] Call Trace:
[ 60.692821] <TASK>
[ 60.693960] ? __pfx_verbose+0x10/0x10
[ 60.695656] ? __pfx_disasm_kfunc_name+0x10/0x10
[ 60.697495] check_cond_jmp_op+0x16f7/0x39b0
[ 60.699237] do_check+0x58fa/0xab10
...
Further analysis shows the warning is at line 4302 as below:
4294 /* static subprog call instruction, which
4295 * means that we are exiting current subprog,
4296 * so only r1-r5 could be still requested as
4297 * precise, r0 and r6-r10 or any stack slot in
4298 * the current frame should be zero by now
4299 */
4300 if (bt_reg_mask(bt) & ~BPF_REGMASK_ARGS) {
4301 verbose(env, "BUG regs %x\n", bt_reg_mask(bt));
4302 WARN_ONCE(1, "verifier backtracking bug");
4303 return -EFAULT;
4304 }
With the below test (also in the next patch):
__used __naked static void __bpf_jmp_r10(void)
{
asm volatile (
"r2 = 2314885393468386424 ll;"
"goto +0;"
"if r2 <= r10 goto +3;"
"if r1 >= -1835016 goto +0;"
"if r2 <= 8 goto +0;"
"if r3 <= 0 goto +0;"
"exit;"
::: __clobber_all);
}
SEC("?raw_tp")
__naked void bpf_jmp_r10(void)
{
asm volatile (
"r3 = 0 ll;"
"call __bpf_jmp_r10;"
"r0 = 0;"
"exit;"
::: __clobber_all);
}
The following is the verifier failure log:
0: (18) r3 = 0x0 ; R3_w=0
2: (85) call pc+2
caller:
R10=fp0
callee:
frame1: R1=ctx() R3_w=0 R10=fp0
5: frame1: R1=ctx() R3_w=0 R10=fp0
; asm volatile (" \ @ verifier_precision.c:184
5: (18) r2 = 0x20202000256c6c78 ; frame1: R2_w=0x20202000256c6c78
7: (05) goto pc+0
8: (bd) if r2 <= r10 goto pc+3 ; frame1: R2_w=0x20202000256c6c78 R10=fp0
9: (35) if r1 >= 0xffe3fff8 goto pc+0 ; frame1: R1=ctx()
10: (b5) if r2 <= 0x8 goto pc+0
mark_precise: frame1: last_idx 10 first_idx 0 subseq_idx -1
mark_precise: frame1: regs=r2 stack= before 9: (35) if r1 >= 0xffe3fff8 goto pc+0
mark_precise: frame1: regs=r2 stack= before 8: (bd) if r2 <= r10 goto pc+3
mark_preci
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: b53: do not enable EEE on bcm63xx
BCM63xx internal switches do not support EEE, but provide multiple RGMII
ports where external PHYs may be connected. If one of these PHYs are EEE
capable, we may try to enable EEE for the MACs, which then hangs the
system on access of the (non-existent) EEE registers.
Fix this by checking if the switch actually supports EEE before
attempting to configure it. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-tcp: sanitize request list handling
Validate the request in nvme_tcp_handle_r2t() to ensure it's not part of
any list, otherwise a malicious R2T PDU might inject a loop in request
list processing. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: save the SR_SUM status over switches
When threads/tasks are switched we need to ensure the old execution's
SR_SUM state is saved and the new thread has the old SR_SUM state
restored.
The issue was seen under heavy load especially with the syz-stress tool
running, with crashes as follows in schedule_tail:
Unable to handle kernel access to user memory without uaccess routines
at virtual address 000000002749f0d0
Oops [#1]
Modules linked in:
CPU: 1 PID: 4875 Comm: syz-executor.0 Not tainted
5.12.0-rc2-syzkaller-00467-g0d7588ab9ef9 #0
Hardware name: riscv-virtio,qemu (DT)
epc : schedule_tail+0x72/0xb2 kernel/sched/core.c:4264
ra : task_pid_vnr include/linux/sched.h:1421 [inline]
ra : schedule_tail+0x70/0xb2 kernel/sched/core.c:4264
epc : ffffffe00008c8b0 ra : ffffffe00008c8ae sp : ffffffe025d17ec0
gp : ffffffe005d25378 tp : ffffffe00f0d0000 t0 : 0000000000000000
t1 : 0000000000000001 t2 : 00000000000f4240 s0 : ffffffe025d17ee0
s1 : 000000002749f0d0 a0 : 000000000000002a a1 : 0000000000000003
a2 : 1ffffffc0cfac500 a3 : ffffffe0000c80cc a4 : 5ae9db91c19bbe00
a5 : 0000000000000000 a6 : 0000000000f00000 a7 : ffffffe000082eba
s2 : 0000000000040000 s3 : ffffffe00eef96c0 s4 : ffffffe022c77fe0
s5 : 0000000000004000 s6 : ffffffe067d74e00 s7 : ffffffe067d74850
s8 : ffffffe067d73e18 s9 : ffffffe067d74e00 s10: ffffffe00eef96e8
s11: 000000ae6cdf8368 t3 : 5ae9db91c19bbe00 t4 : ffffffc4043cafb2
t5 : ffffffc4043cafba t6 : 0000000000040000
status: 0000000000000120 badaddr: 000000002749f0d0 cause:
000000000000000f
Call Trace:
[<ffffffe00008c8b0>] schedule_tail+0x72/0xb2 kernel/sched/core.c:4264
[<ffffffe000005570>] ret_from_exception+0x0/0x14
Dumping ftrace buffer:
(ftrace buffer empty)
---[ end trace b5f8f9231dc87dda ]---
The issue comes from the put_user() in schedule_tail
(kernel/sched/core.c) doing the following:
asmlinkage __visible void schedule_tail(struct task_struct *prev)
{
...
if (current->set_child_tid)
put_user(task_pid_vnr(current), current->set_child_tid);
...
}
the put_user() macro causes the code sequence to come out as follows:
1: __enable_user_access()
2: reg = task_pid_vnr(current);
3: *current->set_child_tid = reg;
4: __disable_user_access()
The problem is that we may have a sleeping function as argument which
could clear SR_SUM causing the panic above. This was fixed by
evaluating the argument of the put_user() macro outside the user-enabled
section in commit 285a76bb2cf5 ("riscv: evaluate put_user() arg before
enabling user access")"
In order for riscv to take advantage of unsafe_get/put_XXX() macros and
to avoid the same issue we had with put_user() and sleeping functions we
must ensure code flow can go through switch_to() from within a region of
code with SR_SUM enabled and come back with SR_SUM still enabled. This
patch addresses the problem allowing future work to enable full use of
unsafe_get/put_XXX() macros without needing to take a CSR bit flip cost
on every access. Make switch_to() save and restore SR_SUM. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: fix uprobe pte be overwritten when expanding vma
Patch series "Fix uprobe pte be overwritten when expanding vma".
This patch (of 4):
We encountered a BUG alert triggered by Syzkaller as follows:
BUG: Bad rss-counter state mm:00000000b4a60fca type:MM_ANONPAGES val:1
And we can reproduce it with the following steps:
1. register uprobe on file at zero offset
2. mmap the file at zero offset:
addr1 = mmap(NULL, 2 * 4096, PROT_NONE, MAP_PRIVATE, fd, 0);
3. mremap part of vma1 to new vma2:
addr2 = mremap(addr1, 4096, 2 * 4096, MREMAP_MAYMOVE);
4. mremap back to orig addr1:
mremap(addr2, 4096, 4096, MREMAP_MAYMOVE | MREMAP_FIXED, addr1);
In step 3, the vma1 range [addr1, addr1 + 4096] will be remap to new vma2
with range [addr2, addr2 + 8192], and remap uprobe anon page from the vma1
to vma2, then unmap the vma1 range [addr1, addr1 + 4096].
In step 4, the vma2 range [addr2, addr2 + 4096] will be remap back to the
addr range [addr1, addr1 + 4096]. Since the addr range [addr1 + 4096,
addr1 + 8192] still maps the file, it will take vma_merge_new_range to
expand the range, and then do uprobe_mmap in vma_complete. Since the
merged vma pgoff is also zero offset, it will install uprobe anon page to
the merged vma. However, the upcomming move_page_tables step, which use
set_pte_at to remap the vma2 uprobe pte to the merged vma, will overwrite
the newly uprobe pte in the merged vma, and lead that pte to be orphan.
Since the uprobe pte will be remapped to the merged vma, we can remove the
unnecessary uprobe_mmap upon merged vma.
This problem was first found in linux-6.6.y and also exists in the
community syzkaller:
https://lore.kernel.org/all/000000000000ada39605a5e71711@google.com/T/ |
| In the Linux kernel, the following vulnerability has been resolved:
dm: limit swapping tables for devices with zone write plugs
dm_revalidate_zones() only allowed new or previously unzoned devices to
call blk_revalidate_disk_zones(). If the device was already zoned,
disk->nr_zones would always equal md->nr_zones, so dm_revalidate_zones()
returned without doing any work. This would make the zoned settings for
the device not match the new table. If the device had zone write plug
resources, it could run into errors like bdev_zone_is_seq() reading
invalid memory because disk->conv_zones_bitmap was the wrong size.
If the device doesn't have any zone write plug resources, calling
blk_revalidate_disk_zones() will always correctly update device. If
blk_revalidate_disk_zones() fails, it can still overwrite or clear the
current disk->nr_zones value. In this case, DM must restore the previous
value of disk->nr_zones, so that the zoned settings will continue to
match the previous value that it fell back to.
If the device already has zone write plug resources,
blk_revalidate_disk_zones() will not correctly update them, if it is
called for arbitrary zoned device changes. Since there is not much need
for this ability, the easiest solution is to disallow any table reloads
that change the zoned settings, for devices that already have zone plug
resources. Specifically, if a device already has zone plug resources
allocated, it can only switch to another zoned table that also emulates
zone append. Also, it cannot change the device size or the zone size. A
device can switch to an error target. |
| In the Linux kernel, the following vulnerability has been resolved:
coresight: holding cscfg_csdev_lock while removing cscfg from csdev
There'll be possible race scenario for coresight config:
CPU0 CPU1
(perf enable) load module
cscfg_load_config_sets()
activate config. // sysfs
(sys_active_cnt == 1)
...
cscfg_csdev_enable_active_config()
lock(csdev->cscfg_csdev_lock)
deactivate config // sysfs
(sys_activec_cnt == 0)
cscfg_unload_config_sets()
<iterating config_csdev_list> cscfg_remove_owned_csdev_configs()
// here load config activate by CPU1
unlock(csdev->cscfg_csdev_lock)
iterating config_csdev_list could be raced with config_csdev_list's
entry delete.
To resolve this race , hold csdev->cscfg_csdev_lock() while
cscfg_remove_owned_csdev_configs() |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: don't warn when if there is a FW error
iwl_trans_reclaim is warning if it is called when the FW is not alive.
But if it is called when there is a pending restart, i.e. after a FW
error, there is no need to warn, instead - return silently. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: copy_verifier_state() should copy 'loop_entry' field
The bpf_verifier_state.loop_entry state should be copied by
copy_verifier_state(). Otherwise, .loop_entry values from unrelated
states would poison env->cur_state.
Additionally, env->stack should not contain any states with
.loop_entry != NULL. The states in env->stack are yet to be verified,
while .loop_entry is set for states that reached an equivalent state.
This means that env->cur_state->loop_entry should always be NULL after
pop_stack().
See the selftest in the next commit for an example of the program that
is not safe yet is accepted by verifier w/o this fix.
This change has some verification performance impact for selftests:
File Program Insns (A) Insns (B) Insns (DIFF) States (A) States (B) States (DIFF)
---------------------------------- ---------------------------- --------- --------- -------------- ---------- ---------- -------------
arena_htab.bpf.o arena_htab_llvm 717 426 -291 (-40.59%) 57 37 -20 (-35.09%)
arena_htab_asm.bpf.o arena_htab_asm 597 445 -152 (-25.46%) 47 37 -10 (-21.28%)
arena_list.bpf.o arena_list_del 309 279 -30 (-9.71%) 23 14 -9 (-39.13%)
iters.bpf.o iter_subprog_check_stacksafe 155 141 -14 (-9.03%) 15 14 -1 (-6.67%)
iters.bpf.o iter_subprog_iters 1094 1003 -91 (-8.32%) 88 83 -5 (-5.68%)
iters.bpf.o loop_state_deps2 479 725 +246 (+51.36%) 46 63 +17 (+36.96%)
kmem_cache_iter.bpf.o open_coded_iter 63 59 -4 (-6.35%) 7 6 -1 (-14.29%)
verifier_bits_iter.bpf.o max_words 92 84 -8 (-8.70%) 8 7 -1 (-12.50%)
verifier_iterating_callbacks.bpf.o cond_break2 113 107 -6 (-5.31%) 12 12 +0 (+0.00%)
And significant negative impact for sched_ext:
File Program Insns (A) Insns (B) Insns (DIFF) States (A) States (B) States (DIFF)
----------------- ---------------------- --------- --------- -------------------- ---------- ---------- ------------------
bpf.bpf.o lavd_init 7039 14723 +7684 (+109.16%) 490 1139 +649 (+132.45%)
bpf.bpf.o layered_dispatch 11485 10548 -937 (-8.16%) 848 762 -86 (-10.14%)
bpf.bpf.o layered_dump 7422 1000001 +992579 (+13373.47%) 681 31178 +30497 (+4478.27%)
bpf.bpf.o layered_enqueue 16854 71127 +54273 (+322.02%) 1611 6450 +4839 (+300.37%)
bpf.bpf.o p2dq_dispatch 665 791 +126 (+18.95%) 68 78 +10 (+14.71%)
bpf.bpf.o p2dq_init 2343 2980 +637 (+27.19%) 201 237 +36 (+17.91%)
bpf.bpf.o refresh_layer_cpumasks 16487 674760 +658273 (+3992.68%) 1770 65370 +63600 (+3593.22%)
bpf.bpf.o rusty_select_cpu 1937 40872 +38935 (+2010.07%) 177 3210 +3033 (+1713.56%)
scx_central.bpf.o central_dispatch 636 2687 +2051 (+322.48%) 63 227 +164 (+260.32%)
scx_nest.bpf.o nest_init 636 815 +179 (+28.14%) 60 73 +13 (+21.67%)
scx_qmap.bpf.o qmap_dispatch
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: ti: k3-udma-glue: Drop skip_fdq argument from k3_udma_glue_reset_rx_chn
The user of k3_udma_glue_reset_rx_chn() e.g. ti_am65_cpsw_nuss can
run on multiple platforms having different DMA architectures.
On some platforms there can be one FDQ for all flows in the RX channel
while for others there is a separate FDQ for each flow in the RX channel.
So far we have been relying on the skip_fdq argument of
k3_udma_glue_reset_rx_chn().
Instead of relying on the user to provide this information, infer it
based on DMA architecture during k3_udma_glue_request_rx_chn() and save it
in an internal flag 'single_fdq'. Use that flag at
k3_udma_glue_reset_rx_chn() to deicide if the FDQ needs
to be cleared for every flow or just for flow 0.
Fixes the below issue on ti_am65_cpsw_nuss driver on AM62-SK.
> ip link set eth1 down
> ip link set eth0 down
> ethtool -L eth0 rx 8
> ip link set eth0 up
> modprobe -r ti_am65_cpsw_nuss
[ 103.045726] ------------[ cut here ]------------
[ 103.050505] k3_knav_desc_pool size 512000 != avail 64000
[ 103.050703] WARNING: CPU: 1 PID: 450 at drivers/net/ethernet/ti/k3-cppi-desc-pool.c:33 k3_cppi_desc_pool_destroy+0xa0/0xa8 [k3_cppi_desc_pool]
[ 103.068810] Modules linked in: ti_am65_cpsw_nuss(-) k3_cppi_desc_pool snd_soc_hdmi_codec crct10dif_ce snd_soc_simple_card snd_soc_simple_card_utils display_connector rtc_ti_k3 k3_j72xx_bandgap tidss drm_client_lib snd_soc_davinci_mcas
p drm_dma_helper tps6598x phylink snd_soc_ti_udma rti_wdt drm_display_helper snd_soc_tlv320aic3x_i2c typec at24 phy_gmii_sel snd_soc_ti_edma snd_soc_tlv320aic3x sii902x snd_soc_ti_sdma sa2ul omap_mailbox drm_kms_helper authenc cfg80211 r
fkill fuse drm drm_panel_orientation_quirks backlight ip_tables x_tables ipv6 [last unloaded: k3_cppi_desc_pool]
[ 103.119950] CPU: 1 UID: 0 PID: 450 Comm: modprobe Not tainted 6.13.0-rc7-00001-g9c5e3435fa66 #1011
[ 103.119968] Hardware name: Texas Instruments AM625 SK (DT)
[ 103.119974] pstate: 80000005 (Nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 103.119983] pc : k3_cppi_desc_pool_destroy+0xa0/0xa8 [k3_cppi_desc_pool]
[ 103.148007] lr : k3_cppi_desc_pool_destroy+0xa0/0xa8 [k3_cppi_desc_pool]
[ 103.154709] sp : ffff8000826ebbc0
[ 103.158015] x29: ffff8000826ebbc0 x28: ffff0000090b6300 x27: 0000000000000000
[ 103.165145] x26: 0000000000000000 x25: 0000000000000000 x24: ffff0000019df6b0
[ 103.172271] x23: ffff0000019df6b8 x22: ffff0000019df410 x21: ffff8000826ebc88
[ 103.179397] x20: 000000000007d000 x19: ffff00000a3b3000 x18: 0000000000000000
[ 103.186522] x17: 0000000000000000 x16: 0000000000000000 x15: 000001e8c35e1cde
[ 103.193647] x14: 0000000000000396 x13: 000000000000035c x12: 0000000000000000
[ 103.200772] x11: 000000000000003a x10: 00000000000009c0 x9 : ffff8000826eba20
[ 103.207897] x8 : ffff0000090b6d20 x7 : ffff00007728c180 x6 : ffff00007728c100
[ 103.215022] x5 : 0000000000000001 x4 : ffff000000508a50 x3 : ffff7ffff6146000
[ 103.222147] x2 : 0000000000000000 x1 : e300b4173ee6b200 x0 : 0000000000000000
[ 103.229274] Call trace:
[ 103.231714] k3_cppi_desc_pool_destroy+0xa0/0xa8 [k3_cppi_desc_pool] (P)
[ 103.238408] am65_cpsw_nuss_free_rx_chns+0x28/0x4c [ti_am65_cpsw_nuss]
[ 103.244942] devm_action_release+0x14/0x20
[ 103.249040] release_nodes+0x3c/0x68
[ 103.252610] devres_release_all+0x8c/0xdc
[ 103.256614] device_unbind_cleanup+0x18/0x60
[ 103.260876] device_release_driver_internal+0xf8/0x178
[ 103.266004] driver_detach+0x50/0x9c
[ 103.269571] bus_remove_driver+0x6c/0xbc
[ 103.273485] driver_unregister+0x30/0x60
[ 103.277401] platform_driver_unregister+0x14/0x20
[ 103.282096] am65_cpsw_nuss_driver_exit+0x18/0xff4 [ti_am65_cpsw_nuss]
[ 103.288620] __arm64_sys_delete_module+0x17c/0x25c
[ 103.293404] invoke_syscall+0x44/0x100
[ 103.297149] el0_svc_common.constprop.0+0xc0/0xe0
[ 103.301845] do_el0_svc+0x1c/0x28
[ 103.305155] el0_svc+0x28/0x98
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
clk: sunxi-ng: h616: Reparent GPU clock during frequency changes
The H616 manual does not state that the GPU PLL supports
dynamic frequency configuration, so we must take extra care when changing
the frequency. Currently any attempt to do device DVFS on the GPU lead
to panfrost various ooops, and GPU hangs.
The manual describes the algorithm for changing the PLL
frequency, which the CPU PLL notifier code already support, so we reuse
that to reparent the GPU clock to GPU1 clock during frequency
changes. |
| In the Linux kernel, the following vulnerability has been resolved:
kasan: avoid sleepable page allocation from atomic context
apply_to_pte_range() enters the lazy MMU mode and then invokes
kasan_populate_vmalloc_pte() callback on each page table walk iteration.
However, the callback can go into sleep when trying to allocate a single
page, e.g. if an architecutre disables preemption on lazy MMU mode enter.
On s390 if make arch_enter_lazy_mmu_mode() -> preempt_enable() and
arch_leave_lazy_mmu_mode() -> preempt_disable(), such crash occurs:
[ 0.663336] BUG: sleeping function called from invalid context at ./include/linux/sched/mm.h:321
[ 0.663348] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 2, name: kthreadd
[ 0.663358] preempt_count: 1, expected: 0
[ 0.663366] RCU nest depth: 0, expected: 0
[ 0.663375] no locks held by kthreadd/2.
[ 0.663383] Preemption disabled at:
[ 0.663386] [<0002f3284cbb4eda>] apply_to_pte_range+0xfa/0x4a0
[ 0.663405] CPU: 0 UID: 0 PID: 2 Comm: kthreadd Not tainted 6.15.0-rc5-gcc-kasan-00043-gd76bb1ebb558-dirty #162 PREEMPT
[ 0.663408] Hardware name: IBM 3931 A01 701 (KVM/Linux)
[ 0.663409] Call Trace:
[ 0.663410] [<0002f3284c385f58>] dump_stack_lvl+0xe8/0x140
[ 0.663413] [<0002f3284c507b9e>] __might_resched+0x66e/0x700
[ 0.663415] [<0002f3284cc4f6c0>] __alloc_frozen_pages_noprof+0x370/0x4b0
[ 0.663419] [<0002f3284ccc73c0>] alloc_pages_mpol+0x1a0/0x4a0
[ 0.663421] [<0002f3284ccc8518>] alloc_frozen_pages_noprof+0x88/0xc0
[ 0.663424] [<0002f3284ccc8572>] alloc_pages_noprof+0x22/0x120
[ 0.663427] [<0002f3284cc341ac>] get_free_pages_noprof+0x2c/0xc0
[ 0.663429] [<0002f3284cceba70>] kasan_populate_vmalloc_pte+0x50/0x120
[ 0.663433] [<0002f3284cbb4ef8>] apply_to_pte_range+0x118/0x4a0
[ 0.663435] [<0002f3284cbc7c14>] apply_to_pmd_range+0x194/0x3e0
[ 0.663437] [<0002f3284cbc99be>] __apply_to_page_range+0x2fe/0x7a0
[ 0.663440] [<0002f3284cbc9e88>] apply_to_page_range+0x28/0x40
[ 0.663442] [<0002f3284ccebf12>] kasan_populate_vmalloc+0x82/0xa0
[ 0.663445] [<0002f3284cc1578c>] alloc_vmap_area+0x34c/0xc10
[ 0.663448] [<0002f3284cc1c2a6>] __get_vm_area_node+0x186/0x2a0
[ 0.663451] [<0002f3284cc1e696>] __vmalloc_node_range_noprof+0x116/0x310
[ 0.663454] [<0002f3284cc1d950>] __vmalloc_node_noprof+0xd0/0x110
[ 0.663457] [<0002f3284c454b88>] alloc_thread_stack_node+0xf8/0x330
[ 0.663460] [<0002f3284c458d56>] dup_task_struct+0x66/0x4d0
[ 0.663463] [<0002f3284c45be90>] copy_process+0x280/0x4b90
[ 0.663465] [<0002f3284c460940>] kernel_clone+0xd0/0x4b0
[ 0.663467] [<0002f3284c46115e>] kernel_thread+0xbe/0xe0
[ 0.663469] [<0002f3284c4e440e>] kthreadd+0x50e/0x7f0
[ 0.663472] [<0002f3284c38c04a>] __ret_from_fork+0x8a/0xf0
[ 0.663475] [<0002f3284ed57ff2>] ret_from_fork+0xa/0x38
Instead of allocating single pages per-PTE, bulk-allocate the shadow
memory prior to applying kasan_populate_vmalloc_pte() callback on a page
range. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: ufs: exynos: Disable iocc if dma-coherent property isn't set
If dma-coherent property isn't set then descriptors are non-cacheable
and the iocc shareability bits should be disabled. Without this UFS can
end up in an incompatible configuration and suffer from random cache
related stability issues. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: prevent hang on link training fail
[Why]
When link training fails, the phy clock will be disabled. However, in
enable_streams, it is assumed that link training succeeded and the
mux selects the phy clock, causing a hang when a register write is made.
[How]
When enable_stream is hit, check if link training failed. If it did, fall
back to the ref clock to avoid a hang and keep the system in a recoverable
state. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: harden block_group::bg_list against list_del() races
As far as I can tell, these calls of list_del_init() on bg_list cannot
run concurrently with btrfs_mark_bg_unused() or btrfs_mark_bg_to_reclaim(),
as they are in transaction error paths and situations where the block
group is readonly.
However, if there is any chance at all of racing with mark_bg_unused(),
or a different future user of bg_list, better to be safe than sorry.
Otherwise we risk the following interleaving (bg_list refcount in parens)
T1 (some random op) T2 (btrfs_mark_bg_unused)
!list_empty(&bg->bg_list); (1)
list_del_init(&bg->bg_list); (1)
list_move_tail (1)
btrfs_put_block_group (0)
btrfs_delete_unused_bgs
bg = list_first_entry
list_del_init(&bg->bg_list);
btrfs_put_block_group(bg); (-1)
Ultimately, this results in a broken ref count that hits zero one deref
early and the real final deref underflows the refcount, resulting in a WARNING. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix hang while freeing sigtrap event
Perf can hang while freeing a sigtrap event if a related deferred
signal hadn't managed to be sent before the file got closed:
perf_event_overflow()
task_work_add(perf_pending_task)
fput()
task_work_add(____fput())
task_work_run()
____fput()
perf_release()
perf_event_release_kernel()
_free_event()
perf_pending_task_sync()
task_work_cancel() -> FAILED
rcuwait_wait_event()
Once task_work_run() is running, the list of pending callbacks is
removed from the task_struct and from this point on task_work_cancel()
can't remove any pending and not yet started work items, hence the
task_work_cancel() failure and the hang on rcuwait_wait_event().
Task work could be changed to remove one work at a time, so a work
running on the current task can always cancel a pending one, however
the wait / wake design is still subject to inverted dependencies when
remote targets are involved, as pictured by Oleg:
T1 T2
fd = perf_event_open(pid => T2->pid); fd = perf_event_open(pid => T1->pid);
close(fd) close(fd)
<IRQ> <IRQ>
perf_event_overflow() perf_event_overflow()
task_work_add(perf_pending_task) task_work_add(perf_pending_task)
</IRQ> </IRQ>
fput() fput()
task_work_add(____fput()) task_work_add(____fput())
task_work_run() task_work_run()
____fput() ____fput()
perf_release() perf_release()
perf_event_release_kernel() perf_event_release_kernel()
_free_event() _free_event()
perf_pending_task_sync() perf_pending_task_sync()
rcuwait_wait_event() rcuwait_wait_event()
Therefore the only option left is to acquire the event reference count
upon queueing the perf task work and release it from the task work, just
like it was done before 3a5465418f5f ("perf: Fix event leak upon exec and file release")
but without the leaks it fixed.
Some adjustments are necessary to make it work:
* A child event might dereference its parent upon freeing. Care must be
taken to release the parent last.
* Some places assuming the event doesn't have any reference held and
therefore can be freed right away must instead put the reference and
let the reference counting to its job. |
