| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: Fix NULL tty_dev dereference in rfcomm_dev_shutdown
syzbot hit a NULL pointer dereference in rfcomm_dev_shutdown() when an
RFCOMM tty is closed.
rfcomm_dev_add() puts the new device on rfcomm_dev_list first and only
then registers the tty device and saves it in dev->tty_dev. If that
registration fails, dev->tty_dev is never set at all. The device can be
looked up in the meantime, so an open() of /dev/rfcommN gets through
rfcomm_tty_install() and attaches to it. When that tty is closed again,
rfcomm_dev_shutdown() uses dev->tty_dev without checking it:
Oops: general protection fault, probably for non-canonical address
KASAN: null-ptr-deref in range [0x0000000000000040-0x0000000000000047]
RIP: 0010:rfcomm_dev_shutdown+0x48/0xb0 net/bluetooth/rfcomm/tty.c:131
Call Trace:
tty_port_shutdown+0x1bf/0x220 drivers/tty/tty_port.c:372
tty_port_close+0x4e/0x150 drivers/tty/tty_port.c:705
tty_release+0x359/0x1670 drivers/tty/tty_io.c:1718
__fput+0x418/0xa50 fs/file_table.c:512
rfcomm_dev_destruct() already copes with a NULL dev->tty_dev. Add the
same check to rfcomm_dev_shutdown(), so the tty device is only moved
when it was actually registered. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: connect the session socket without rfcomm_mutex
An RFCOMM connect() issued while a BR/EDR link is being authenticated
makes lockdep report a circular dependency, and the reported cycle is a
real AB/BA between rfcomm_mutex and hdev->lock.
rfcomm_security_cfm() is called from the HCI event path, which already
holds hdev->lock:
hci_rx_work()
hci_event_packet()
hci_cc_read_enc_key_size() [hdev->lock]
hci_encrypt_cfm() [hci_cb_list_lock]
rfcomm_security_cfm() [rfcomm_mutex]
while an RFCOMM connect() from userspace takes the same two locks the
other way round:
rfcomm_sock_connect()
rfcomm_dlc_open() [rfcomm_mutex]
__rfcomm_dlc_open()
rfcomm_session_create()
kernel_connect()
l2cap_sock_connect()
l2cap_chan_connect() [hdev->lock]
WARNING: possible circular locking dependency detected
kworker/u131:1/1128 is trying to acquire lock:
rfcomm_mutex, at: rfcomm_security_cfm+0x31/0x3e0 [rfcomm]
but task is already holding lock:
hci_cb_list_lock, at: hci_cc_read_enc_key_size+0x1d2/0xcc0
Chain exists of:
rfcomm_mutex --> &hdev->lock --> hci_cb_list_lock
hci_auth_complete_evt() and hci_encrypt_change_evt() reach the callback
the same way.
Both orders have to be seen in the same boot, which is why a BR/EDR
connection alone is not enough to show it: a session set up by the
remote side is created by rfcomm_accept_connection() in krfcommd, which
calls kernel_accept() and never takes hdev->lock under rfcomm_mutex.
Connecting a device that authenticates and encrypts the link and then
calling connect() on an RFCOMM socket towards any address - the connect
does not have to succeed, the order is recorded before the page timeout
- reports it every time.
Only the session socket has to be connected with the lock held, and it
does not: nothing else can see the socket before it is put on the
session list. So connect it first and take rfcomm_mutex afterwards,
which removes the rfcomm_mutex -> hdev->lock order for good, rather
than keeping the HCI event path out of rfcomm_mutex.
rfcomm_session_create() becomes rfcomm_session_connect(), which returns
the connected socket without touching the session list, and
rfcomm_dlc_open() adds the session once it holds the lock again. If
another opener added a session for the same pair while this socket was
connecting, that session is used and this socket is dropped.
__rfcomm_dlc_open() now takes the session it should use, and its state
check runs after the lock is re-acquired, so a DLC that was opened or
closed in the meantime is still handled.
Over an existing ACL link the connection can complete before the
session reaches the list, and the wakeup from the socket callback is
then lost, so krfcommd is woken once the session is visible.
Connecting without the lock opens a window in which the socket can be
closed. The DLC is not on a session yet, so rfcomm_dlc_close() finds
nothing to do and returns without touching it, and rfcomm_dlc_open()
would then attach a DLC whose owner is gone. rfcomm_dlc_close() now
marks such a DLC with RFCOMM_CLOSED, and rfcomm_dlc_open() checks the
mark once it holds rfcomm_mutex again and drops the socket instead of
attaching the DLC. The mark is cleared when an open starts, so a DLC
that is reused is not affected. This covers both callers of
rfcomm_dlc_open(), the socket and the tty layer. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: free the skb when the DLC has no owner
rfcomm_recv_data() hands the skb to d->data_ready() and returns 0
without freeing it, so the callback owns the skb from that point on.
The tty implementation frees it when the DLC has been detached from its
device:
static void rfcomm_dev_data_ready(struct rfcomm_dlc *dlc,
struct sk_buff *skb)
{
struct rfcomm_dev *dev = dlc->owner;
if (!dev) {
kfree_skb(skb);
return;
}
The socket implementation returns without freeing it, and the skb is
leaked.
A connected DLC can have no owner: rfcomm_sock_destruct() clears
d->owner, while the DLC itself stays on the session until it is closed.
Data frames that arrive in that window still find d->state ==
BT_CONNECTED in rfcomm_recv_data() and are handed to the callback, one
leaked skb each.
The leak does not stop on its own either. The remote runs out of
credits only once RFCOMM_RX_THROTTLED is set, and for a socket the only
place that sets it is rfcomm_sk_data_ready() itself, below the return.
rfcomm_process_dlcs() keeps granting credits, so the remote keeps
sending and the leak keeps growing.
Free the skb, as the tty side does. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: Serialize concurrent connect calls
iso_sock_connect() checks the socket state before taking the socket lock
and drops the lock again before setting up a connection. Two callers can
both pass the admission check while the socket is open or bound.
Caller A can copy its destination for route selection, then caller B can
replace the socket destination before A binds or connects the CIS. A
then uses B's destination with the route selected for its own request.
B can also proceed after A attaches a connection and sets BT_CONNECT.
For deferred BIS setup, B can bind a second BIS and overwrite
iso_pi(sk)->conn, leaving the first connection's reference and conn->sk
back-pointer stranded. Concurrent CIS connects can likewise replace the
socket's connection. Later teardown only detaches the current connection,
so a callback on the old connection can race with socket release and
access a freed socket.
KASAN reported:
BUG: KASAN: slab-use-after-free in iso_sock_hold+0xf7/0x1b0
Call Trace:
iso_sock_hold+0xf7/0x1b0
iso_conn_del+0x7b/0x1d0
iso_connect_cfm+0x186/0x16a0
hci_conn_failed+0x154/0x280
hci_abort_conn_sync+0x3dc/0x7d0
hci_cmd_sync_work+0x173/0x300
Allocated by task 121:
sk_alloc+0x2b/0x6d0
bt_sock_alloc+0x29/0x370
iso_sock_alloc.constprop.0+0x19/0x300
iso_sock_create+0x94/0x100
Freed by task 121:
kfree+0x121/0x3c0
__sk_destruct+0x42b/0x540
iso_sock_release+0x29d/0x340
__sock_release+0xa1/0x260
Check admission under the socket lock and mark the connect operation in
progress before publishing its destination. Keep that flag set across
route lookup and connection setup, rejecting another connect with
-EBADFD before it can change the destination or attach a connection.
Clear the flag after either helper returns, including on failure, so a
failed setup can be retried.
A separate flag is needed because the socket lock must be released before
acquiring the HCI device lock, while BT_CONNECT requires an attached
connection. Keep the existing state transitions and the deferred CIS
completion through iso_sock_recvmsg().
Reject an existing socket attachment in __iso_chan_add() before taking
a new reference or publishing either pointer, so every caller preserves
the connection association. Keep the same-socket, same-connection success
case for deferred CIS setup. Reject an attached socket before BIS setup
so a reusable BIS is not claimed before the attachment is rejected.
In CIS setup, reject a different HCI connection before iso_conn_add()
and drop the per-attempt HCI hold directly. An unowned iso_conn may still
carry another reference after detachment, so its destruction cannot be
relied on to release that hold.
iso_listen_bis() creates a fresh PA HCI/ISO pair under the device lock,
so the temporary iso_conn_put() frees the ISO candidate and drops its
HCI hold on rejection. iso_conn_ready() uses a freshly allocated,
unpublished child with no connection, making the socket-side rejection
unreachable. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: Reject concurrent BIS listener setup
iso_sock_listen() drops the socket lock before calling iso_listen_bis()
to preserve the hdev->lock ordering. Two concurrent listen() calls on
the same broadcast socket can therefore both observe BT_BOUND. Caller
A can attach connA and release the locks, then caller B can acquire
them and attach connB before A publishes BT_LISTEN.
__iso_chan_add() checks whether connB already has a socket, but not
whether the socket already has a connection. The second attachment
overwrites iso_pi(sk)->conn, leaking the connA reference and leaving
connA->sk intact. Socket teardown follows connB, so later events on
connA can cause a stale socket access.
Recheck BT_BOUND and require iso_pi(sk)->conn to be NULL after taking
both the HCI device and socket locks in iso_listen_bis(). The connection
check also covers the interval between attachment and publication of
BT_LISTEN. Reject a competing setup with -EBADFD through the existing
unlock path before allocating another connection.
A recorded KASAN report from an instrumented kernel shows:
BUG: KASAN: slab-use-after-free in iso_sock_hold+0x119/0x1f0
Call Trace:
iso_sock_hold+0x119/0x1f0
iso_conn_del+0xe4/0x270
hci_disconn_complete_evt+0x351/0x8c0
hci_event_packet+0x71b/0xb20
hci_rx_work+0x293/0x730
Allocated by task 93:
sk_prot_alloc+0x113/0x220
sk_alloc+0x2b/0x6d0
bt_sock_alloc+0x29/0x370
iso_sock_alloc.constprop.0+0x19/0x300
iso_sock_create+0x94/0x100
Freed by task 93:
kfree+0x121/0x3c0
__sk_destruct+0x42b/0x540
iso_sock_release+0x29d/0x340
__sock_release+0xa1/0x260
sock_close+0x10/0x20 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Fix command skb lifetime during scan setup
During PA sync scan setup, hci_le_set_ext_scan_param_sync() gets the
address used for the PA_LINK lookup from hci_sent_cmd_data(). The
returned pointer borrows storage from sent_cmd or req_skb, without
holding a reference to either skb.
The scan worker runs on req_workqueue while hci_cmd_work() runs on the
separate device workqueue. After the scan worker loads sent_cmd, the
command worker can free and replace it before hci_sent_cmd_data()
dereferences the skb. The command payload can also be freed between
returning from the helper and comparing the address. The connection
lookup's RCU critical section does not protect the command skb.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_sent_cmd_data+0x27c/0x2f0
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
hci_sent_cmd_data+0x27c/0x2f0
hci_le_set_scan_param_sync+0x43a/0x850
hci_passive_scan_sync+0xb09/0x1460
hci_update_passive_scan_sync+0x47c/0x6e0
hci_le_pa_create_sync+0x200/0xa70
hci_cmd_sync_work+0x13c/0x290
Allocated by task 95:
skb_clone+0x13f/0x340
hci_cmd_work+0x2a9/0x7e0
Freed by task 95:
kmem_cache_free+0xba/0x3a0
hci_cmd_work+0x29c/0x7e0
Use hdev->lock to serialize the address snapshot with sent_cmd
replacement. Protect req_skb replacement and completion cleanup with
the same lock because the helper falls back to that skb. Copy the
address before releasing the lock and use the copy for the existing
RCU-protected connection lookup. Release the mutex before sending or
waiting for commands, preserving the lookup and completion ordering. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sock: Serialize dead-device detachment
Rebinding an HCI socket after its controller is unregistered can race
monitor control replay and crash the kernel. hci_sock_bind() clears
hci_pi(sk)->hdev and drops the device reference under only the socket
lock, whereas send_monitor_control_replay() holds hci_sk_list.lock for
reading.
Replay can observe a non-NULL hdev, then bind can clear it and drop the
last reference before create_monitor_ctrl_open() reads hdev->id. This
can cause a NULL pointer dereference if the pointer is reloaded, or a
use-after-free if the old pointer is retained.
The kernel reported:
KASAN: null-ptr-deref in range [0x0000000000000068-0x000000000000006f]
RIP: 0010:create_monitor_ctrl_open+0x579/0x800
Call Trace:
hci_sock_bind+0xd96/0x1190
__sys_bind+0x166/0x200
__x64_sys_bind+0x6d/0xb0
do_syscall_64+0xdd/0x4a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The same missing serialization lets hci_send_to_sock() select a socket
for the old device and queue its frame after bind has detached the socket
or installed a new binding.
Take hci_sk_list.lock for writing when clearing the device pointer and
resetting the socket state. This waits for existing replay and delivery
readers to finish before detachment and prevents later readers from
using the old binding. Keep hci_dev_put() outside the critical section
because the final device release can sleep. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: futex: untag the user pointer before the atomic access
access_ok() checks untagged_addr(uaddr), but arch_futex_atomic_op_inuser()
and futex_atomic_cmpxchg_inatomic() hand the raw uaddr to the inline asm
amoswap/amoadd/.../lr.w+sc.w through the "+m" (*uaddr) operand. When the
tagged address ABI is enabled (CONFIG_RISCV_ISA_SUPM, prctl
PR_SET_TAGGED_ADDR_CTRL with PMLEN != 0), those two addresses differ: a
user pointer whose top PMLEN bits hold a tag passes access_ok() after
untagging, but the atomic is then performed on the still-tagged raw
address.
Supervisor-mode data accesses are not subject to the U-mode pointer
masking (that is governed by menvcfg.PMM, which the kernel does not set),
so hardware does not strip the tag for the kernel's own access. With
Sv57 and PMLEN=16 the tag bits overlap the canonical-address bits, so a
tagged pointer can name a canonical kernel virtual address (e.g. in the
linear map) whose untagged form is a valid user address. An unprivileged
process can thus make FUTEX_WAKE_OP perform an atomic read-modify-write on
an arbitrary kernel address, with the matching FUTEX_OP_CMP_* result
serving as a read oracle.
get_user()/put_user()/raw_copy_{to,from}_user() already untag the pointer
after the access_ok() check; do the same in the futex helpers so the
atomic operates on the address that was actually validated. |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: errata: select RISCV_ALTERNATIVE_EARLY for THEAD GHOSTWRITE
errata_probe_ghostwrite() only marks the CPU as vulnerable when it is
called at the RISCV_ALTERNATIVES_EARLY_BOOT stage, and the mitigation
in ghostwrite_enable_mitigation() only takes effect if the vulnerable
state was recorded before the boot alternatives are patched.
The early boot stage is only executed when CONFIG_RISCV_ALTERNATIVE_EARLY
is enabled, which currently is only selected by ERRATA_THEAD_MAE. In a
kernel built with ERRATA_THEAD_GHOSTWRITE=y but ERRATA_THEAD_MAE=n, the
early alternatives never run, so ghostwrite_state is never set to
VULNERABLE: ghostwrite_enable_mitigation() returns false, xtheadvector
remains enabled, and sysfs reports "Not affected" on a vulnerable
T-Head C9xx CPU.
Select RISCV_ALTERNATIVE_EARLY from ERRATA_THEAD_GHOSTWRITE so that the
vulnerability is detected in the early boot stage and the default
mitigation is applied. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: tps6594-regulator: Fix n_linear_ranges for TPS65224 BUCK2-4
The TPS65224 BUCK2, BUCK3 and BUCK4 descriptors pass 4 as
n_linear_ranges, but tps65224_bucks_2_3_4_ranges[] only has two
entries, covering selectors 0x00-0x45.
The linear range helpers loop over n_linear_ranges entries, so any
lookup of a selector above 0x45 reads past the end of the array and
treats whatever follows it as two more ranges. This happens on the
normal registration path when the core checks the voltage constraints
against every selector. TPS652G1 uses the same descriptors and is
affected too.
Use ARRAY_SIZE() so the count always matches the table. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: of: fill in supply names in of_regulator_bulk_get_all()
of_regulator_bulk_get_all() returns an array it allocated itself, and
fills in only the consumer of each entry. Every other way of getting a
bulk array has the supply name set, because the caller provides it, and
the core expects it to be there: regulator_bulk_enable() prints it when
a supply fails to enable, so a caller that hands such an array to it
dereferences uninitialised memory on that path.
Copy each name into the array's own allocation, right behind the
entries, so that it shares the array's lifetime and callers still have
nothing extra to free. That also retires the fixed 64 byte stack buffer
the names were assembled in, which is_supply_name() never bounded the
copy against. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: ltc3676: don't read the write-only HRST and CLIRQ registers
HRST (0x1e) and CLIRQ (0x1f) are write-only command strobes. Writing HRST
triggers a hard reset of the chip and writing CLIRQ clears the interrupt;
reading them returns nothing useful, and the read itself fires the command.
The result is that a plain register dump resets the board:
cat /sys/kernel/debug/regmap/2-003c/registers
walks every readable register, hits HRST, and the board reboots.
Split the callback back in two so HRST and CLIRQ stay writable but are no
longer readable. The readable range is left unchanged
(LTC3676_BUCK1 ... LTC3676_IRQSTAT). |
| In the Linux kernel, the following vulnerability has been resolved:
power: sequencing: pcie-m2: Fix leaking array from of_regulator_bulk_get_all()
of_regulator_bulk_get_all() allocates the consumers array and hands it to
the caller, who is expected to free it at an appropriate time.
pwrseq-pcie-m2.c never did, leading to a memory leak.
Add an explicit kfree() for the consumers array. |
| In the Linux kernel, the following vulnerability has been resolved:
optee: register TEE devices only once fully initialized
optee_probe() called tee_device_register() on both the client and the
supplicant device before the rest of struct optee had been initialized.
tee_device_register() calls cdev_device_add(), which does two things at
once: it creates /dev/tee0 and /dev/teepriv0, and it links the device
into the tee class so that class_find_device() can find it. From that
moment on the device is reachable both from user space via tee_open()
and from kernel space via tee_client_open_context(). The only gate in
teedev_open() is tee_device_get(), which merely checks that
teedev->desc is non-NULL, which was already set by tee_device_alloc().
Therefore, there is effectively no gate at all.
A context opened in that window can run against a struct optee where
- optee->call_queue.mutex is not initialized by optee_cq_init()
- optee->supp mutex and completions is not initialized by
optee_supp_init()
- optee->rpmb_dev_mutex is not initialized yet,
- the message argument cache is not initialized by
optee_shm_arg_cache_init()
- optee->ctx is still NULL
Any open session or invoke during this window takes uninitialized
mutexes and dereferences a NULL pointer.
Fix it by moving both tee_device_register() calls down to the point
where all of struct optee is set up.
[JW: adding fixes and cc] |
| Use after free in Windows Installer allows an authorized attacker to elevate privileges locally. |
| Heap-based buffer overflow in Microsoft Office Word allows an unauthorized attacker to execute code over a network. |
| Out-of-bounds read in Microsoft Office PowerPoint allows an unauthorized attacker to disclose information over a network. |
| The FluentCart A New Era of eCommerce – Faster, Lighter, and Simpler plugin for WordPress is vulnerable to Insecure Direct Object Reference in all versions up to, and including, 1.7.0 via the 'order_id + billing_address_id (also shipping_address_id)' parameter due to missing validation on a user controlled key. This makes it possible for unauthenticated attackers to read and exfiltrate another customer's stored billing and shipping address PII — including street address, city, state, postcode, phone number, company name, VAT number, and legal registration ID — by enumerating sequential AUTO_INCREMENT order and address ID pairs. The id-equality guard intended to restrict address reuse is bypassed because the attacker controls both halves of the compared pair, and the unauthenticated AJAX entry point imposes only a soft rate limit of 5 requests per 60 seconds rather than any authentication or ownership check. |
| IBM MQ could allow a remote attacker with queue manager control or man-in-the-middle access on unencrypted channels to cause a denial of service in client applications using asynchronous message consumption due to improper validation of queue name length values. |
| Part-DB is an open source inventory management system for electronic components. Prior to version 2.13.2, Part-DB contains a spreadsheet formula injection vulnerability in the part import/export workflow. An authenticated user with permission to import parts can import a CSV file containing formula-prefixed values, such as =1+1, into user-controlled part fields. When the affected part is later exported as an XLSX spreadsheet, Part-DB writes the attacker-controlled value using PhpSpreadsheet's setCellValue() method without neutralising spreadsheet formula characters. As a result, the exported XLSX file contains an executable spreadsheet formula cell rather than a plain text value. If another user exports and opens the spreadsheet, the formula may be evaluated by their spreadsheet software. This issue has been patched in version 2.13.2. |
