| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: at76c50x-usb: avoid length underflow in at76_guess_freq()
at76_guess_freq() checks only that the received frame is at least a bare
802.11 header (24 bytes) before subtracting the fixed management-body
offset:
len -= el_off;
For both beacon and probe response frames, el_off is 36. If the frame is
shorter than el_off, subtracting it causes the calculated IE length to
wrap. The length is eventually passed to cfg80211_find_elem_match() as a
very large unsigned value, so the element walk runs beyond the RX skb.
This path is reached from at76_rx_tasklet() while scanning. If the device
delivers a truncated beacon or probe response, the oversized IE length
causes an out-of-bounds read during scanning.
Skip the IE lookup if the frame does not reach the variable elements,
before subtracting el_off. |
| In the Linux kernel, the following vulnerability has been resolved:
firewire: net: Fix fragmented datagram reassembly
fwnet_frag_new() keeps a sorted list of received fragments for a partial
datagram. When a new fragment is adjacent to an existing fragment, the
code checks whether the new fragment also closes the gap to the next or
previous list entry.
Those neighbor lookups currently assume that the current fragment always
has a real next or previous fragment. At a list edge, the next or
previous entry is the list head, not a struct fwnet_fragment_info.
The gap checks also compare against the old edge of the current fragment
instead of the edge after adding the new fragment. As a result, a
fragment that bridges two existing ranges may leave two adjacent ranges
unmerged, so fwnet_pd_is_complete() can miss a complete datagram.
Check for the list head before looking up the neighboring fragment, and
compare the neighbor against the new fragment's far edge when deciding
whether to merge all three ranges.
This issue was found by a static analysis checker and confirmed by
manual source review. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath6kl: fix OOB read from firmware IE lengths in connect event
The firmware-controlled beacon_ie_len, assoc_req_len, and assoc_resp_len
fields in ath6kl_wmi_connect_event_rx() are not validated against the
buffer length. Their sum (up to 765) can exceed the actual WMI event
data, causing out-of-bounds reads during IE parsing and state corruption
of wmi->is_wmm_enabled.
Add a check that the total IE length fits within the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: tas2781: bound firmware description string parsing
The TAS2781 firmware parser reads several variable-length description
strings with strlen() before checking that the string terminator is
present inside the firmware blob. A malformed firmware image without a
NUL terminator can therefore make the parser walk past the end of the
firmware buffer before the later size checks run.
Add a small bounded string-length helper and use it for all description
fields that are parsed from the firmware buffer. Keep the existing size
checks for the fixed bytes that follow each string. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: validate DFS referral PathConsumed
parse_dfs_referrals() validates that the response contains the fixed
referral entry array and, on for-next, the per-referral string offsets.
However, the response also contains a PathConsumed value that is later
used for DFS path parsing.
If a malformed response provides a PathConsumed value larger than the
search name, later DFS parsing can advance beyond the end of the path.
Validate PathConsumed against the search name length before storing it in
the parsed referral. |
| In the Linux kernel, the following vulnerability has been resolved:
net/packet: avoid fanout hook re-registration after unregister
packet_set_ring() temporarily detaches a socket from packet delivery while
reconfiguring its ring. It records the previous running state, clears
po->num, unregisters the protocol hook when needed, drops po->bind_lock,
and later restores po->num and re-registers the hook from the saved
was_running value.
That unlocked window can race with NETDEV_UNREGISTER. The notifier can
observe the socket as not running, skip __unregister_prot_hook(), and
invalidate the per-socket binding by setting po->ifindex to -1 and clearing
po->prot_hook.dev. A one-member fanout group can still retain its shared
fanout hook device pointer. When packet_set_ring() resumes, re-registering
solely from the stale was_running state can re-add the fanout hook after
the device has been unregistered.
Treat po->ifindex == -1 as an invalidated binding after reacquiring
po->bind_lock. This is distinct from ifindex 0, the normal
unbound/wildcard state: ifindex -1 marks an existing device binding that
was invalidated when the device was unregistered. Restore po->num as
before, but do not re-register the hook if device unregister already
detached the socket. |
| In the Linux kernel, the following vulnerability has been resolved:
rds: drop incoming messages that cross network namespace boundaries
rds_find_bound() looks up the destination socket using a global
rhashtable keyed solely on (addr, port, scope_id). Network namespaces
are not part of the key, so a sender in netns A can deliver an incoming
message (inc) to a socket that lives in a different netns B.
When this happens, inc->i_conn points to an rds_connection whose c_net
is netns A, but the receiving rs lives in netns B. Once the child
process that created netns A exits, cleanup_net() calls
rds_loop_exit_net() -> rds_loop_kill_conns() -> rds_conn_destroy(),
freeing that connection. If the survivor socket in netns B still holds
the inc, any subsequent dereference of inc->i_conn is a use-after-free.
There are two dangerous sites in rds_clear_recv_queue():
1. inc->i_conn->c_lcong (offset 88 of freed rds_connection, size 200)
read via rds_recv_rcvbuf_delta() -- confirmed by KASAN.
2. inc->i_conn->c_trans->inc_free(inc) (function pointer at offset 80)
called via rds_inc_put() when the inc refcount reaches zero -- same
race window, potential call-through-freed-object primitive.
The bug is reachable from unprivileged user namespaces
(CLONE_NEWUSER + CLONE_NEWNET), available since Linux 3.8.
Fix this by rejecting the delivery in rds_recv_incoming() when the
socket returned by rds_find_bound() belongs to a different network
namespace than the connection that carried the message. Use the
existing rds_conn_net() / sock_net() helpers and net_eq() for the
comparison. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Wait for completion instead of returning early in iommu_completion_wait()
need_sync is a per-IOMMU flag shared by all domains and devices behind
that IOMMU. It is set whenever a command is queued with sync == true and
cleared when a completion-wait (CWAIT) command is queued. However, a
cleared need_sync only means that a covering CWAIT has been queued, not
that all previously queued commands have actually completed in hardware.
iommu_completion_wait() read need_sync locklessly and returned early
when it was false. This breaks the "block until all previously queued
commands have completed" contract in a multi-CPU scenario:
CPU2: queue inv-B => need_sync = true
CPU1: queue CWAIT(N); need_sync = false; then wait_on_sem(N)
CPU2: read need_sync == false => return 0 (no wait!)
CPU2 returns without waiting for any sequence number even though its
inv-B may not have completed yet (CWAIT(N), queued after inv-B, has not
been signaled). CPU2 then proceeds to, for example, free page-table
pages while the IOMMU can still walk stale translations, opening a
use-after-free window. This is a logical race in the meaning of the
flag, not a memory-visibility issue, so barriers alone do not help.
Fix it without losing the optimization of avoiding redundant CWAIT
commands: take iommu->lock before testing need_sync, and when it is
false do not return early but wait for the last allocated sequence
number (cmd_sem_val). Since need_sync == false implies no sync command
was queued after the last CWAIT, that CWAIT is FIFO-ordered after every
not-yet-completed command, so waiting for its sequence number guarantees
all prior commands (possibly queued by another CPU) have completed. The
common path with pending work is unchanged and no extra hardware command
is issued. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: fix auth_chunk_list capacity check in sctp_auth_ep_add_chunkid
sctp_auth_ep_add_chunkid() uses SCTP_NUM_CHUNK_TYPES (20) as the
capacity limit for ep->auth_chunk_list, allowing it to hold up to
20 chunk entries (param_hdr.length up to 24). However, the copy
destination asoc->c.auth_chunks in struct sctp_cookie is only
SCTP_AUTH_MAX_CHUNKS (16) entries (20 bytes). When more than 16
chunks are added, sctp_association_init() memcpy overflows the
destination by up to 4 bytes.
Fix by using SCTP_AUTH_MAX_CHUNKS as the capacity limit, matching
the destination capacity. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: validate stream count in sctp_process_strreset_inreq()
When processing a RESET_IN_REQUEST from a peer,
sctp_process_strreset_inreq() derives the stream count from the
parameter length but does not check whether the resulting
RESET_OUT_REQUEST would exceed SCTP_MAX_CHUNK_LEN.
The OUT request header (sctp_strreset_outreq, 16 bytes) is 8 bytes
larger than the IN request header (sctp_strreset_inreq, 8 bytes).
Generally, the IP payload is bounded to 65535 bytes, so the stream
list cannot be large enough to trigger the overflow. However, on
interfaces with MTU > 65535 (e.g., loopback with IPv6 jumbograms), a
stream list that fits within the incoming IN parameter can cause a
__u16 overflow in sctp_make_strreset_req() when computing the OUT
request size, leading to an undersized skb allocation and a kernel
BUG:
net/core/skbuff.c:207 skb_panic
net/core/skbuff.c:2625 skb_put
net/sctp/sm_make_chunk.c:1535 sctp_addto_chunk
net/sctp/sm_make_chunk.c:3695 sctp_make_strreset_req
net/sctp/stream.c:655 sctp_process_strreset_inreq
The local setsockopt path validates the generated reset request size.
However, for an incoming-only reset, it accounts for the smaller IN
request even though the peer must generate an OUT request with the same
stream list. Such a request cannot be completed successfully by the
peer.
Reject peer IN requests whose corresponding OUT request would exceed
SCTP_MAX_CHUNK_LEN. Also tighten the local check so it does not send an
IN request that would require an oversized OUT request from the peer. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: auth: verify auth requirement when auth_chunk is NULL
sctp_auth_chunk_verify() returns true unconditionally when
chunk->auth_chunk is NULL, silently skipping authentication.
This is incorrect when:
1. skb_clone() failed in the BH receive path, leaving auth_chunk
NULL. In sctp_endpoint_bh_rcv() asoc is NULL for new
connections, so the early sctp_auth_recv_cid() check cannot
catch this.
2. No AUTH chunk precedes COOKIE-ECHO, so skb_clone() is never
called and auth_chunk remains NULL.
Fix by checking sctp_auth_recv_cid() when auth_chunk is NULL:
if authentication is required, return false to drop the chunk;
otherwise continue normally. |
| In the Linux kernel, the following vulnerability has been resolved:
vmxnet3: fix BUG_ON in vmxnet3_get_hdr_len() for Geneve packets
vmxnet3_get_hdr_len() assumes gdesc->rcd.v4/v6/tcp always describe the
outer header, but for a Geneve-encapsulated packet the device can set
them based on the inner header instead, signalled by the
VMXNET3_RCD_HDR_INNER_SHIFT bit in the completion descriptor. Since the
function never skips the outer encapsulation, this mismatch triggers:
- BUG_ON(hdr.ipv4->protocol != IPPROTO_TCP), because the outer
protocol is UDP (Geneve), not TCP.
- BUG_ON(hdr.eth->h_proto != ...), when the tunnel's outer and inner
IP versions differ (e.g. outer IPv6/inner IPv4 or vice versa).
Check VMXNET3_RCD_HDR_INNER_SHIFT up front and bail out, since the
function cannot locate the inner header it would need to parse. Also
convert the remaining BUG_ON()s in this function to return 0
defensively. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/vm: Fix SVM leak on resv obj alloc failure in xe_vm_create()
Commit 9e9787414882 ("drm/xe/userptr: replace xe_hmm with gpusvm") made
xe_svm_init() unconditional in xe_vm_create() and extended it to also
initialize a "simple" gpusvm state for non-fault-mode VMs. The matching
xe_svm_fini() call in xe_vm_close_and_put() was updated to run
unconditionally, but the error unwind path in xe_vm_create() was not.
On the drm_gpuvm_resv_object_alloc() failure path, xe_svm_init() has
already succeeded but xe_svm_fini() is only called when
XE_VM_FLAG_FAULT_MODE is set. For non-fault-mode VMs this leaves
vm->svm.gpusvm partially initialized and leaks the resources allocated
by drm_gpusvm_init().
For fault-mode VMs, xe_svm_init() additionally acquires the pagemap
owner via drm_pagemap_acquire_owner() and the pagemaps via
xe_svm_get_pagemaps(). Those resources are released by xe_svm_close(),
not xe_svm_fini(). On the same error path, xe_svm_close() is not
called either, so fault-mode VMs leak the pagemap owner and pagemaps.
Fix both leaks:
- Call xe_svm_fini() unconditionally on the err_svm_fini path, matching
the unconditional xe_svm_init() call. Move the vm->size = 0
assignment out of the conditional so the xe_vm_is_closed() assert in
xe_svm_fini() (and xe_svm_close()) holds for both modes.
- Call xe_svm_close() for fault-mode VMs before xe_svm_fini(), matching
the ordering used in xe_vm_close_and_put().
(cherry picked from commit ca2a3587d577ba764e0fe628fb676244fc33ddd4) |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: fix u16 MTU truncation in media and bearer MTU validation
Both TIPC_NL_MEDIA_SET and TIPC_NL_BEARER_SET accept user-supplied
MTU values but only enforce a minimum bound, not a maximum. When a user
sets the MTU to a value exceeding U16_MAX (65535), it passes validation
but is silently truncated when assigned to u16 fields l->mtu and
l->advertised_mtu in tipc_link_create(). Values like 65536 (0x10000)
truncate to 0, causing a division by zero in tipc_link_set_queue_limits()
which computes TIPC_MAX_PUBL / (l->mtu / ITEM_SIZE). Other overflowing
values (e.g. 65537-131071) produce small incorrect MTU values, resulting
in link malfunction behaviors.
Crash stack (triggered as unprivileged user via user namespace):
tipc_link_set_queue_limits net/tipc/link.c:2531
tipc_link_create net/tipc/link.c:520
tipc_node_check_dest net/tipc/node.c:1279
tipc_disc_rcv net/tipc/discover.c:252
tipc_rcv net/tipc/node.c:2129
tipc_udp_recv net/tipc/udp_media.c:392
Two independent paths lack the upper bound check:
1. tipc_udp_mtu_bad() -- called from __tipc_nl_media_set() (MEDIA_SET)
2. inline check in __tipc_nl_bearer_set() at bearer.c:1160 (BEARER_SET)
Fix both by rejecting MTU values above U16_MAX. |
| In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: restrict socket creation to the initial network namespace
QRTR keeps its entire port and node state in module-global variables
that are not partitioned per network namespace: qrtr_local_nid is a
single global node id (always 1) and qrtr_ports is a single global
xarray. qrtr_port_lookup() and qrtr_local_enqueue() operate on that
global state with no network-namespace check, and qrtr_create() places
no restriction on the namespace a socket is created in.
As a result an unprivileged process that creates an AF_QIPCRTR socket
in a separate network namespace, e.g. via
unshare(CLONE_NEWUSER | CLONE_NEWNET), can send QRTR datagrams -
including control-plane messages such as QRTR_TYPE_NEW_SERVER - to QRTR
sockets owned by another namespace, and vice versa. The receiving
socket sees such a message as coming from node id 1, indistinguishable
from a legitimate local client, breaking the isolation that network
namespaces are expected to provide.
QRTR is a transport to global hardware endpoints (the modem and other
remote processors) and has no per-namespace semantics; its in-kernel
name service already creates its socket in init_net only. Confine the
socket family to the initial network namespace, as other
non-namespace-aware socket families do (see llc_ui_create() and the
ieee802154 socket code). |
| In the Linux kernel, the following vulnerability has been resolved:
rds: tcp: unregister sysctl before tearing down listen socket
rds_tcp_exit_net() frees the per-netns RDS TCP listen socket via
rds_tcp_kill_sock() before unregistering the per-netns sysctl table. Since
rds_tcp_skbuf_handler() derives the netns from
rtn->rds_tcp_listen_sock->sk, a concurrent sysctl write can race with
netns teardown and dereference the freed socket/sk.
KASAN reports the race as:
BUG: KASAN: slab-use-after-free in rds_tcp_skbuf_handler+0x2aa/0x2e0
rds_tcp_skbuf_handler net/rds/tcp.c:721
proc_sys_call_handler fs/proc/proc_sysctl.c
vfs_write fs/read_write.c
__x64_sys_pwrite64 fs/read_write.c
Fix this by unregistering the RDS TCP sysctl table before calling
rds_tcp_kill_sock(). unregister_net_sysctl_table() prevents new sysctl
handlers from starting and waits for in-flight handlers to finish, so
the listen socket can then be released safely. The fix was tested
against the linked reproducer. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Fix cork use-after-free in tcp_bpf_sendmsg()
tcp_bpf_sendmsg() keeps msg_tx across sk_stream_wait_memory(), which
drops and reacquires the socket lock. Its error path tries to decide
whether msg_tx names the local temporary message by comparing it with
the current value of psock->cork.
This comparison is unsafe when two threads send on the same socket:
Thread A Thread B
msg_tx = psock->cork
sk_msg_alloc() fails
sk_stream_wait_memory()
releases the socket lock acquires the socket lock
completes the cork
psock->cork = NULL
frees the cork
reacquires the socket lock
msg_tx != psock->cork
sk_msg_free(msg_tx)
The stale cork is therefore mistaken for the local temporary message
and freed again. KASAN reported:
BUG: KASAN: slab-use-after-free in sk_msg_free+0x49/0x50
Read of size 4 at addr ffff88810c908800 by task poc/90
Call Trace:
sk_msg_free+0x49/0x50
tcp_bpf_sendmsg+0x14f5/0x1cc0
__sys_sendto+0x32c/0x3a0
__x64_sys_sendto+0xdb/0x1b0
Allocated by task 89:
__kasan_kmalloc+0x8f/0xa0
tcp_bpf_sendmsg+0x16b3/0x1cc0
Freed by task 91:
__kasan_slab_free+0x43/0x70
kfree+0x131/0x3c0
tcp_bpf_sendmsg+0xec3/0x1cc0
msg_tx can only name the stack-local tmp or the shared cork. Check for
tmp directly so a changed psock->cork cannot turn a shared message into
an apparent local one. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe: Hold a dma-buf reference for imported BOs
An imported dma-buf BO is created as a ttm_bo_type_sg BO whose
reservation object is the exporter's dma_buf->resv. The importer,
however, only takes a dma-buf reference after a successful
dma_buf_dynamic_attach(). Until then nothing keeps the exporter alive,
so if the exporter is freed while the BO still references its resv, a
later access to that resv is a use-after-free:
Oops: general protection fault, probably for non-canonical address
0x6b6b6b6b6b6b6b9c
Workqueue: ttm ttm_bo_delayed_delete [ttm]
RIP: 0010:mutex_can_spin_on_owner+0x3f/0xc0
This can be reached on two paths:
- dma_buf_dynamic_attach() fails, or
- ttm_bo_init_reserved() fails during BO creation.
In both cases the BO already has bo->base.resv pointing at the exporter
resv, and sg BOs are always torn down via ttm_bo_delayed_delete(), which
locks bo->base.resv asynchronously - potentially after the exporter has
been freed.
Take the dma-buf reference in xe_bo_init_locked(), before
ttm_bo_init_reserved(), so it also covers a creation failure there, and
release it in xe_ttm_bo_destroy(). The reference is held for the whole
BO lifetime, keeping the shared resv alive on every path.
v2:
- Reworked the fix to avoid creating the imported sg BO before
dma_buf_dynamic_attach() succeeds.
- Attach with importer_priv == NULL and make invalidate_mappings ignore
incomplete imports.
v3:
- Dropped the xe-side reordering approach since importer_priv must be
valid when dma_buf_dynamic_attach() publishes the attachment.
- Per Christian's suggestion on the v1 thread, keyed the check on
import_attach rather than removing the sg guard entirely.
- Fixes both xe and amdgpu in a single TTM patch.
v4:
- Moved import_attach check to after dma_resv_copy_fences() so fences
are copied before returning for successful imports (Thomas).
- Removed exporter-alive claim from commit message (Thomas).
v5:
- Add drm/xe patch to keep imported sg BOs off the LRU before attach
succeeds; the TTM fix alone is not sufficient for xe if the BO is
already LRU-visible. (Thomas)
v4 patch:
https://patchwork.freedesktop.org/patch/736663/?series=169129&rev=2
- Patch 1 (drm/ttm) carries Christian's Reviewed-by from v4.
v6:
- Reworked the fix based on Thomas' suggestion. Instead of the TTM resv
individualization (v1-v5) plus the xe off-LRU/placement handling (v5),
just hold a dma-buf reference for the imported BO lifetime so the
shared resv can never be freed while the BO still references it.
Single xe patch, no TTM change. (Thomas)
- Take the reference in xe_bo_init_locked() before ttm_bo_init_reserved()
so a TTM creation failure is covered too (Thomas).
- Dropped the v5 series (drm/ttm + drm/xe off-LRU); the off-LRU approach
also regressed in CI BAT via ttm_bo_pipeline_gutting() creating a ghost
BO that outlived the exporter.
Link to v5: https://patchwork.freedesktop.org/series/169984/
v7:
- Move changelog above --- so it stays in the commit message.
- Reorder changelog entries oldest-to-newest. (Thomas)
(cherry picked from commit 3516f3fae6be35642f8f06f8a218da6425c0306a) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/vm: Fix BO prefetch with CONSULT_MEM_ADVISE_PREF_LOC
When prefetch region is DRM_XE_CONSULT_MEM_ADVISE_PREF_LOC for a BO VMA,
the code used it as an index into region_to_mem_type[], causing an
out-of-bounds access since the value is -1.
Resolve the preferred location for BO VMAs directly: local VRAM on dGFX
(using the BO's tile placement) or system memory on iGPU.
Discovered using AI-assisted static analysis confirmed by Intel Product
Security.
v2:
-Fix null dereference
(cherry picked from commit d9a4906ac03be9f6ed3f3b45c56c866b867fd75b) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/pt: Reset current_op in xe_pt_update_ops_init()
xe_pt_update_ops_init() fails to reset current_op to 0. On the
vm_bind path, ops_execute() calls xe_pt_update_ops_prepare() inside
the xe_validation_guard() / drm_exec_until_all_locked() loop. When
that loop retries due to lock contention or OOM eviction
(drm_exec_retry_on_contention() / xe_validation_retry_on_oom()),
xe_pt_update_ops_prepare() runs again on the same vops, and each
call to bind_op_prepare() increments current_op without resetting it.
After N retries current_op exceeds the array size allocated by
xe_vma_ops_alloc(), causing an out-of-bounds write into
SLUB-poisoned memory and a subsequent UAF crash in
xe_migrate_update_pgtables_cpu() when reading the corrupted pt_op->bind.
Also reset needs_svm_lock and needs_invalidation which are derived in
the same prepare pass and would otherwise cause wrong migrate ops
selection and redundant TLB invalidation on retry.
Fix this by resetting current_op, needs_svm_lock and needs_invalidation
in xe_pt_update_ops_init().
v2 (Matt):
- Add details in commit message.
- Add Fixes tag and Cc to stable@vger.kernel.org
(cherry picked from commit 046045543e530605c441063535e7dca0075369a6) |
