| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: ISO: Copy BASE if service data matches EIR_BAA_SERVICE_UUID
Copy the content of a Periodic Advertisement Report to BASE only if
the service UUID is Basic Audio Announcement Service UUID. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Infer zext_dst based on static register liveness analysis
As reported in the thread [1], the verifier's 32-bit operations zero
extension logic is broken. This logic is responsible for correct
semantics of 32-bit operations on s390 architecture.
According to BPF semantics, operation `w1 += 1` is supposed to zero
extend the upper half of the register `r1`. On s390 the JIT relies on
the verifier emitting explicit zero extension before such operations.
The verifier attempts to minimize the amount of zero extensions
inserted by tracking whether upper halves of the 64-bit registers are
ever used. Previously such tracking worked as follows:
- bpf_reg_state->subreg_def field was set by do_check_insn()
for each operation defining lower but not the upper halves
of the register.
- Whenever an operation reading the whole register was verified,
the verifier checked register's subreg_def and set
bpf_insn_aux_data->zext_dst flag as true via a call to
mark_insn_zext() function.
- After the verification was complete, a special pass
bpf_opt_subreg_zext_lo32_rnd_hi32() extended 32-bit operations
with bpf_insn_aux_data->zext_dst set as true by adding
explicit zero extension.
Note that the logic above relies on bpf_reg_state->subreg_def,
which is a property of a current verifier state.
Before the commit [2] two additional steps happened:
- The verifier tracked upper and lower register halves' liveness as
flags REG_LIVE_READ{32,64} in bpf_reg_state->live.
- The function propagate_liveness() called mark_insn_zext()
in order to transfer the knowledge about which registers have
their upper halves alive (and thus might require zero extension).
The commit [2] removed the two steps described above,
hence making possible a situation like below:
- The register's upper half is set and is used on some verification
path P1 and the register happens not to be marked as precise.
- The checkpoint C is created while processing some instruction
between register initialization and usage.
- On some other verification path P2 the register's upper half is not
initialized and that path ends hitting the checkpoint C.
- In such a case the register's initialization on path P2 would lack
zext_dst mark, making it possible for the program to inject
an arbitrary value in the register's upper half.
This commit replaces subreg_def based logic with computing zext_dst
statically, as a part of the bpf_compute_live_registers() analysis:
- The analysis now tracks usage of upper and lower halves of the
registers separately.
- If some instruction defines a 32-bit subregister, but not the whole
register, *and* the upper half of the register is alive after that
instruction, the instruction is marked as zext_dst.
There is one notable drop in precision: whenever a BPF subprogram is
called, all 64 bits of parameter registers are presumed to be used.
The assumption is that such a drop in precision would not inflict
a noticeable performance penalty.
[1] https://lore.kernel.org/bpf/CAGKGUv=sOuqQtA1Ub-5JXfA4FPosJFYKAQE4B79cK+P1erxqtg@mail.gmail.com/
[2] commit 107e16979905 ("bpf: disable and remove registers chain based liveness") |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: set info->band for 802.3 encap offload frames
Unlike the 802.11 TX paths, ieee80211_8023_xmit() does not set
info->band from the channel context on non-MLD interfaces. It stays at
0, so ieee80211_get_tx_rates() uses the wrong band for these frames.
Set it the same way as ieee80211_build_hdr(): drop the frame if there is
no channel context, and leave the band at 0 on MLD interfaces. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: handle empty FILS association request payload
fils_encrypt_assoc_req() accepts a (Re)Association Request frame whose
last element is the FILS Session element. crypt_len is then zero and
aes_siv_encrypt() is called with an empty plaintext.
kmemdup() returns ZERO_SIZE_PTR for a zero-length allocation, so the
unconditional sg_init_one() puts an invalid page into the scatterlist.
With CONFIG_DEBUG_SG this triggers a kernel BUG in sg_set_buf();
without the debug check the bogus page is handed to the crypto backend.
AES-SIV is defined for empty plaintext and the S2V result is then the
complete output, so handle this case before the CTR step, which has
nothing to encrypt. |
| In the Linux kernel, the following vulnerability has been resolved:
smb: client: split cifsFileInfo bitfields to avoid shared-byte RMW races
The invalidHandle, swapfile, oplock_break_cancelled, offload,
and status_file_deleted fields are stored in the same bitfield byte
in struct cifsFileInfo, but are updated in different code paths that
may run simultaneously, and are protected by different locks. Since
bitfield assignments generate byte-level read-modify-write operations,
a modification to one flag can overwrite a concurrent modification to
another flag.
To avoid these races, convert these flags from a bitfield to
separate bool fields. |
| In the Linux kernel, the following vulnerability has been resolved:
net: extend IPv6 exthdr detection of tunneled packets
Commit c4336a07eb6b ("net: correctly handle tunneled traffic on IPV6_CSUM
GSO fallback") split skb_gso_has_extension_hdr() into mutually exclusive
branches on skb->encapsulation. This did not yet address all paths:
1. With skb->encapsulation set, the outer header is not checked. IPv6
tunnels such as ip6_gre and ip6_tunnel add an outer Destination
Options header by default (encap_limit). Their GSO packets skip
software GSO, then skb_csum_hwoffload_help() sees the outer extension
header and calls skb_checksum_help() on the GSO skb, which warns and
drops it.
2. Tunnels over IPv6 without an outer transport header, such as
ip6_tunnel, leave skb->transport_header at the inner transport
header. skb_network_header_len() then spans the outer IPv6, tunnel
and inner IP headers, a false positive.
3. UDP tunnels without an inner network header, such as SCTP-in-UDP or
PSP, have no inner IPv6 header to check. Decide on the outer header
alone.
4. Directly dereferencing inner_ip_hdr(skb)->version without
skb_header_pointer() is unsafe.
Instead, check ipv6_ext_hdr(nexthdr) on the outer IPv6 header and, if
set, on the inner IPv6 header. Read the headers with skb_header_pointer().
Keep the skb_network_header_len() check when !skb->encapsulation to also
catch encapsulated packets without skb->encapsulation (e.g., virtio).
Use the same helper in skb_csum_hwoffload_help(). Its open coded test
has the false positive of (2) and ignores the inner header.
Background: checksum offload of tunneled packets invariants:
Non-GSO skb:
- If the inner packet is CHECKSUM_PARTIAL, Local Checksum Offload computes
the outer checksum in software and the device offloads only the inner L4
checksum.
- If the inner packet is CHECKSUM_NONE (e.g., SCTP-in-UDP, ESP-in-UDP,
Remote Checksum Offload), the device offloads the outer UDP or GRE
checksum instead.
GSO skb:
- A device with NETIF_F_GSO_UDP_TUNNEL_CSUM or NETIF_F_GSO_GRE_CSUM
computes both inner and outer checksums per segment.
The outer checksum is seeded with only the pseudo-header checksum.
A NETIF_F_IPV6_CSUM device must parse through the outer headers to
reach the inner ones. |
| In the Linux kernel, the following vulnerability has been resolved:
rtc: spear: initialize IRQ state before requesting alarm IRQ
devm_request_irq() enables the interrupt before it returns, so the handler
may run while probe is still initializing the device. Initialize the MMIO
address and spinlock before requesting the alarm IRQ. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm: recover after failure to start the frs ams
Reset the port if the tcpm fails to start the FAST_ROLE_SWAP AMS by
initiating error recovery on it.
This helps in cases where some cables (incorrectly) signal an FRS to
an FRS capable port during disconnection. The TCPC autonomously starts
sourcing VBUS on detecting the FRS signal. However, the VBUS sourcing is
left on when the FAST_ROLE_SWAP AMS fails to start (as tcpm_sink_tx_ok
is 0 as CC is open due to the cable disconnect). This is because the
code sets the state to INVALID_STATE without resetting the port state.
Log snippet before changes:
[ 101.401960] AMS FAST_ROLE_SWAP start
[ 101.401971] Sink TX No Go
[ 101.401982] sourcing vbus
[ 101.401987] VBUS on
[ 101.402159] VBUS on
[ 109.257809] CC1: 0 -> 0, CC2: 5 -> 0 [state SNK_READY, polarity 1, disconnected]
[ 111.267442] VBUS on
After changes:
[ 70.541211] AMS FAST_ROLE_SWAP start
[ 70.541220] Sink TX No Go
[ 70.541228] state change SNK_READY -> ERROR_RECOVERY [rev3 NONE_AMS]
[ 70.541362] VBUS on
[ 70.541365] sourcing vbus
[ 70.541367] VBUS on
[ 70.541374] state change ERROR_RECOVERY -> PORT_RESET [rev3 NONE_AMS]
[ 70.541410] disable vbus discharge ret:0
[ 70.543028] Setting usb_comm capable false
[ 70.544009] Setting voltage/current limit 0 mV 0 mA
[ 70.544034] polarity 0
[ 70.544239] Requesting mux state 0, usb-role 0, orientation 0
[ 70.555550] cc:=0
[ 70.555595] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev3 NONE_AMS]
[ 70.555697] VBUS off
[ 70.555702] VBUS VSAFE0V
[ 70.555762] CC1: 5 -> 0, CC2: 0 -> 0 [state PORT_RESET, polarity 0, disconnected]
[ 70.587794] VBUS off
[ 70.587799] VBUS VSAFE0V
[ 70.655672] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms]
[ 70.655682] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev3 NONE_AMS]
[ 70.655686] Start toggling
[ 70.656274] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected] |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: rawnand: cadence: Initialize IRQ state before requesting IRQ
The Cadence NAND interrupt handler uses both the IRQ lock and completion
object. Registering the IRQ before initializing them leaves a window in
which a pending interrupt can access uninitialized synchronization state.
Initialize them before registering the handler. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: zoned: finish active block group cleanup if call_zone_finish() fails
do_zone_finish() clears BLOCK_GROUP_FLAG_ZONE_IS_ACTIVE before finishing
the zones. If call_zone_finish() then fails it returned early, leaving the
now inactive block group on fs_info->zone_active_bgs, leaking its
reference, the BTRFS_FS_NEED_ZONE_FINISH waiters are never woken, and as
its alloc_offset equals the zone capacity btrfs_zone_finish_one_bg() keeps
selecting it, spinning btrfs_zoned_activate_one_bg().
Fall through to the cleanup on failure too and return the error, but keep
the block group read-only as its zones are left inconsistent. |
| In the Linux kernel, the following vulnerability has been resolved:
smb/client: zero-initialize stack-allocated cifs_open_info_data
Stack-allocated cifs_open_info_data may contain random data.
This can make some fields have wrong value if they are not set later. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/hugetlb: initialize gigantic bootmem hugepage struct pages earlier
Gigantic bootmem HugeTLB pages are currently initialized from
hugetlb_init(), but page_alloc_init_late() runs earlier and walks
pageblocks to determine zone contiguity.
If a bootmem HugeTLB region is marked noinit, set_zone_contiguous() can
observe still-uninitialized struct pages through
__pageblock_pfn_to_page(). This may not trigger an immediate failure, but
it can make set_zone_contiguous() compute the wrong zone contiguity state.
If extra poisoned-page checks are added in this path, such as
PF_POISONED_CHECK() in page_zone_id(), it can also trigger an early boot
panic.
Initialize gigantic bootmem HugeTLB struct pages from
page_alloc_init_late(), before zone contiguity is evaluated, so later page
allocator setup only sees valid struct page state. This also makes the
initialization order more natural, as struct pages should be initialized
before later code inspects them. |
| In the Linux kernel, the following vulnerability has been resolved:
perf/x86/intel/uncore: Fix uncore_box ref/unref ordering
In uncore_event_cpu_online(), uncore_box_ref() was called before
uncore_change_context(). uncore_box_ref() gates on box->cpu >= 0,
but box->cpu is still -1 at that point because uncore_change_context()
has not run yet. As a result, the box is never initialized on the
first CPU to come online in a die, leaving it permanently
uninitialized in the single-CPU-per-die case.
Thus, box->refcnt is one count below the true value, and in the CPU
offline path, the box will be torn down on the second-to-last CPU.
In uncore_event_cpu_offline(), uncore_box_unref() was called after
uncore_change_context(), so box->cpu is already -1 when the collector
CPU goes offline, which prevents it from tearing down the box.
Fix by swapping the call order in both paths so that
uncore_box_{ref,unref}() runs at the point where box->cpu reflects
the correct context.
Move allocate_boxes() out of uncore_box_ref() to enable this
reordering. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Fix SCMI device destroy lifetimes
scmi_child_dev_find() drops the reference returned by
device_find_child() before returning the scmi_device pointer. A
concurrent unregister can then release the device while the destroy path
is still using the returned pointer.
Make the lookup helper return the device_find_child() reference and keep
it until scmi_device_destroy() has finished unregistering the child.
Also split device_unregister() in __scmi_device_destroy() so the SCMI bus
ID is not made reusable until after device_del() has removed the old
scmi_dev.N name from sysfs. This avoids a new SCMI device reusing the
same ID while the old device is still registered.
The final device release callback is also a possible cleanup path when
SCMI children are deleted by driver core recursion rather than
__scmi_device_destroy(). Release the SCMI bus ID from a common helper
used by destroy, register-failure and final-release paths, and clear
scmi_dev->id after freeing it so the final release cannot free the same
ID again. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: Only fini scheduler after successful init
msm_ringbuffer_new() destroys a partially initialized ring through
msm_ringbuffer_destroy() when an allocation or scheduler setup step
fails.
If drm_sched_init() fails before it finishes initializing the scheduler,
the failure path still calls drm_sched_fini(). That teardown path assumes
the scheduler work items, lists, and workqueue state were initialized.
Track successful scheduler initialization and call drm_sched_fini() only
after drm_sched_init() returned 0.
This issue was found by a static analysis checker and confirmed by
manual source review.
Patchwork: https://patchwork.freedesktop.org/patch/738905/ |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1: create serial pool adding rdev to array with serialize_policy=1
The following bug has been observed with kernel 7.1.3 after adding a new
rdev to an existing RAID1 array with serialize_policy enabled:
Oops: 0002 [#1]
CPU: 0 UID: 0 PID: 19639 Comm: ext4lazyinit Not tainted 7.1.3-1-default
RIP: _raw_spin_lock_irqsave+0x27/0x50
CR2: 0000000000004960
Call Trace:
wait_for_serialization+0xb9/0x260 [raid1]
raid1_make_request+0x762/0xaff [raid1]
md_handle_request+0x1c9/0x2e0 [md_mod]
The raid1.c code calls wait_for_serialization() if the MD_SERIALIZE_POLICY
is set, and wait_for_serialization assumes that rdev->serial is
initialized. Normally this will be the case for arrays that have
the serialize_policy sysfs attribute set to 1.
But when a new rdev is added to an existing array in bind_rdev_to_array(),
the condition at mddev_create_serial_pool() causes creation of rdev->serial
to be skipped. Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: unwind state on add_interface failure
When mt76_wcid_alloc() fails, mt7915_add_interface() returned without
clearing the vif_mask/omac_mask bits it had already set, without removing
the firmware dev info added earlier, and without clearing a monitor_vif
pointer to the vif mac80211 is about to free. mac80211 does not call
remove_interface() for a failed add, so the indices and firmware dev
entry leaked permanently and testmode could dereference the stale
monitor_vif. Add a proper error unwind. |
| In the Linux kernel, the following vulnerability has been resolved:
ublk: check import_ubuf() return value
import_ubuf() can fail if the address range (provided by the userspace
ublk server) is outside the allowed user address space. Return that 0
bytes were copied if import_ubuf() fails rather than passing an
uninitialized struct iov_iter to ublk_copy_user_pages(). |
| In the Linux kernel, the following vulnerability has been resolved:
thermal: hwmon: Remove hwmon class device along with its parent
The current code creates one hwmon device per thermal zone type and that
device is registered under the first thermal zone of the given type.
That turns out to be problematic when the thermal zone holding the
hwmon device is removed.
For example, say that there are two ACPI thermal zones on a system
/sys/devices/virtual/thermal/thermal_zone0/
/sys/devices/virtual/thermal/thermal_zone1/
The current code registers a hwmon class device for thermal_zone0 only:
/sys/devices/virtual/thermal/thermal_zone0/hwmon0/
because the type is "acpitz" for both of them, but it adds a sysfs
attribute that belongs to thermal_zone1 under it:
/sys/devices/virtual/thermal/thermal_zone0/hwmon0/temp2_input
There is also
/sys/devices/virtual/thermal/thermal_zone0/hwmon0/temp1_input
which belongs to thermal_zone0.
When thermal_zone0 is removed, say because the ACPI thermal driver is
unbound from the underlying platform device, thermal_remove_hwmon_sysfs()
skips the removal of hwmon0 because of the temp2_input attribute
belonging to thermal_zone1 which effectively prevents thermal_zone0
removal from making progress.
Address this by making thermal_remove_hwmon_sysfs() remove the entire
hwmon class device interface for the given thermal zone type when the
thermal zone device holding it is removed.
To prevent races with thermal_add_hwmon_sysfs() that may interfere
with this, carry out the entire addition and removal of hwmon sysfs
interfaces for thermal zones under thermal_hwmon_list_lock.
Also adjust the layout of the labels in thermal_add_hwmon_sysfs() to
the current kernel coding style to align with the new "unlock" label. |
| In the Linux kernel, the following vulnerability has been resolved:
coresight: etm4x: missing cscfg_csdev_disable_active_config() in perf enable
In the perf enable path, there are missing cases where
cscfg_csdev_disable_active_config() is not called:
- Branch broadcast is selected but not supported by the hardware
- etm4_enable_hw() fails
This can lead to a leak of config_desc->active_cnt.
Fix this by properly calling cscfg_csdev_disable_active_config()
in these error paths. |
